25 TOOTMISTEHNOLOOGIA

Tagasi peagrupi juurde

Uued standardid

EVS-EN 60683:2012
Hind 7,93 EUR
Industrial electroheating equipment - Test methods for submerged-arc furnaces
This International Standard specifies test procedures, conditions and methods according to which the main parameters and the main operational characteristics of a submerged-arc furnace (SAF) with rated electrical power levels above 500 kVA are established. This standard is applicable to SAF with one or more electrodes. In order to determine further technical or economic assessments, additional tests may be necessary. Tests for some special equipment for semiconductor converter controlled furnaces, such as controlled rectifiers or controlled a.c. converters, are covered by IEC 60146-1-1.

Asendatud või tühistatud standardid

EVS-HD 599 S1:2003
Test methods for submerged-arc furnaces
Standardizes submerged arc furnace test conditions and methods to determine their main parameters and technical characteristics. Applies to industrial three-phase submerged arc furnaces with rated power level of 1 000 kVA or more. Also applies to furnaces having one or more electrodes, other than three-phase furnaces.
Keel: Inglise

EVS-EN ISO 9409-1:2004
Manipuleerivad tööstusrobotid. Mehaanilised liidesed. Osa 1: Plaadid (kuju A)
This part of ISO 9409 defines the main dimensions, designation and marking for a circular plate as mechanical interface. It is intended to ensure the exchangeability and to keep the orientation of hand-mounted end effectors. This part of ISO 9409 does not define other requirements of the end effector coupling device. This part of ISO 9409 does not contain any correlation of load-carrying ranges, as it is expected that the appropriate interface is selected depending on the application and the load-carrying capacity of the robot.
Keel: Inglise

EVS-EN ISO 9283:2001
Manipulating industrial robots - Performance criteria and related test methods
This standard describes methods of specifying and testing the following performance characteristics of manipulating industrial robots: - pose accuracy and pose repeatebility; multi-directional pose accuracy variation; distance accuracy and distance repeatebility; position; stabilization time; position overshoot; drift of pose characteristics; exchangeability; path accuracy and path repeatebility; path accuracy on reorientation; cornering deviations; path velocity characteristics; minimum posing time; static compliance; weaving deviations.
Keel: Inglise

EVS-EN ISO 9787:1999
Manipulaatoriga tööstusrobotid. Koordinaatsüsteemid ja liigutuste nimetuste süsteemid
Standard defineerib ja määrab kindlaks roboti koordinaatsüsteemid. Standard esitab ka nimetuste süsteemi, mis hõlmab roboti põhiliigutuste esituse. Standardi eesmärk olla toeks robotite väljareguleerimisel, testimisel ja programmeerimisel.
Keel: Inglise

EVS-EN ISO 9946:1999
Manipulating industrial robots - Presentation of characteristics
The standard provides recommendations on how the characteristics of the robots shall be specified by the manufacturer.
Keel: Inglise

EVS-EN ISO 11593:1999
Manipuleerivad tööstusrobotid. Tööorganite automaatvahetuse süsteemid. Sõnastik ja tunnusomaduste esitus
Standard määratleb terminid, mis seonduvad tootmiskeskkonnas kasutatavate manipuleerivate tööstusrobotite tööorganite automaatvahetuse süsteemidega. Terminid on esitatud nende tähise, ühiku, määratluse ja nimetusega. Määratlus sisaldab kohaldatavaid viiteid olemasolevatele standarditele.
Keel: Inglise

EVS-EN ISO 9409-2:2004
Manipulating industrial robots - Mechanical interfaces - Part 2: Shafts
This part of ISO 9409 defines the main dimensions, designation and marking for a shaft with cylindrical projection as mechanical interface. It is intended to ensure the exchangeability and to keep the orientation of hand-mounted end effectors. This part of ISO 9409 does not contain any correlation of load-carrying ranges. The mechanical interfaces specified in this part of ISO 9409 will also find application in simple handling systems which are not covered by the definition of manipulating industrial robots, such as pick-and-place or master-slave units.
Keel: Inglise

EVS-EN ISO 14539:2002
Manipulating industrial robots - Object handling with grasp-type grippers - Vocabulary and presentation of characteristics
This standard focuses on the functionalities of end effectors and concentrates on grasptype grippers as defined in 4.1.2.1. This standard provides terms to describe object handling and terms of functions, structures, and elements of grasp-type grippers.
Keel: Inglise

EVS-EN ISO 10303-210:2003
Industrial automation systems and integration - Product data representation and exchange - Part 210: Application protocol: Electronic assembly, interconnection, and packaging design
This part of ISO 10303 specifies the use of the integrated resources necessary for the scope and information requirements for the design of electronic assemblies, interconnect and packaging.
Keel: Inglise

Kavandite arvamusküsitlus

prEN 13438
Tähtaeg 31.03.2012
Paints and varnishes - Powder organic coatings for galvanized or sherardized steel products for construction purposes
This European Standard specifies performance requirements for organic coating powders and powder organic coatings as applied to finished articles (galvanized or sherardized steel products) for construction purposes. This standard does not set out any performance requirements for the powder coating process itself. Galvanized steel products can be articles batch hot dip galvanized (galvanized after fabrication) or articles consisting of continuously hot-dip galvanized sheet which is then subsequently fabricated. This standard does not apply to articles with zinc-aluminium coatings or aluminium-zinc coatings, or to continuously hot dip galvanized wire. Guidance on cleaning and pre-treatment of the galvanized or sherardized steel products prior to powder coating is provided.
Keel: Inglise

FprEN 61918:2011/FprAA
Tähtaeg 31.03.2012
Industrial communication networks - Installation of communication networks in industrial premises
This International Standard specifies basic requirements for the installation of media for communication networks in industrial premises and within and between the automation islands, of industrial sites. This standard covers balanced and optical fibre cabling. It also covers the cabling infrastructure for wireless media, but not the wireless media itself. Additional media are covered in the IEC 61784-5 series. This standard is a companion standard to the communication networks of the industrial automation islands and especially to the communication networks specified in the IEC 61158 series and the IEC 61784 series. In addition, this standard covers: - the installation of generic telecommunication cabling for industrial premises as specified in ISO/IEC 24702; - the connection between the generic telecommunications cabling specified in ISO/IEC 24702 and the specific communication cabling of an automation island, where an automation outlet (AO) replaces the telecommunication outlet (TO) of ISO/IEC 24702. NOTE If the interface used at the AO does not conform to that specified for the TO of ISO/IEC 24702, the cabling no longer conforms to ISO/IEC 24702 although certain features, including performance, of generic cabling may be retained. This standard provides guidelines that cope with the critical aspects of the industrial automation area (safety, security and environmental aspects such as mechanical, liquid, particulate, climatic, chemicals and electromagnetic interference). This standard does not recognise implementations of power distribution through Ethernet balanced cabling systems that are not specified in IEEE 802.3 and in IEEE 802.3at. This standard deals with the roles of planner, installer, verifier, and acceptance test personnel, administration and maintenance personnel and specifies the relevant responsibilities and/or gives guidance.
Keel: Inglise

FprEN 61918
Tähtaeg 31.03.2012
Industrial communication networks - Installation of communication networks in industrial premises
This International Standard specifies basic requirements for the installation of media for communication networks in industrial premises and within and between the automation islands, of industrial sites. This standard covers balanced and optical fibre cabling. It also covers the cabling infrastructure for wireless media, but not the wireless media itself. Additional media are covered in the IEC 61784-5 series. This standard is a companion standard to the communication networks of the industrial automation islands and especially to the communication networks specified in the IEC 61158 series and the IEC 61784 series. In addition, this standard covers: - the installation of generic telecommunication cabling for industrial premises as specified in ISO/IEC 24702; - the connection between the generic telecommunications cabling specified in ISO/IEC 24702 and the specific communication cabling of an automation island, where an automation outlet (AO) replaces the telecommunication outlet (TO) of ISO/IEC 24702. NOTE If the interface used at the AO does not conform to that specified for the TO of ISO/IEC 24702, the cabling no longer conforms to ISO/IEC 24702 although certain features, including performance, of generic cabling may be retained. This standard provides guidelines that cope with the critical aspects of the industrial automation area (safety, security and environmental aspects such as mechanical, liquid, particulate, climatic, chemicals and electromagnetic interference). This standard does not recognise implementations of power distribution through Ethernet balanced cabling systems that are not specified in IEEE 802.3 and in IEEE 802.3at. This standard deals with the roles of planner, installer, verifier, and acceptance test personnel, administration and maintenance personnel and specifies the relevant responsibilities and/or gives guidance.
Keel: Inglise

EN 62061:2005/FprA1
Tähtaeg 31.03.2012
Masinate ohutus. Ohutusega seotud elektriliste, elektrooniliste ja programmeeritavate elektrooniliste kontrollsüsteemide funktsionaalne ohutus
specifies requirements and makes recommendations for the design, integration and validation of safety-related electrical, electronic and programmable electronic control systems (SRECS) for machines (see Notes 1 and 2). It is applicable to control systems used, either singly or in combination, to carry out safety-related control functions on machines that are not portable by hand while working, including a group of machines working together in a co-ordinated manner.
Keel: Inglise