75 NAFTA JA NAFTATEHNOLOOGIA

Tagasi peagrupi juurde

Uued standardid

EVS-EN 589:2008+A1:2012
Hind 8,72 EUR
Mootorikütused. Vedelgaas. Nõuded ja katsemeetodid KONSOLIDEERITUD TEKST
This European Standard specifies requirements and test methods for marketed and delivered automotive LPG (Liquefied Petroleum Gas). It is applicable to automotive LPG for use in LPG engine vehicles designed to run on automotive LPG. NOTE: For the purposes of this European Standard, the term “% (V/V)” is used to represent the volume fraction. WARNING - Attention is drawn to the risk of fire and explosion when handling LPG and to the hazard to health which arises through inhalation of excessive amounts of LPG. LPG is a highly volatile hydrocarbon liquid which is normally stored under pressure. If the pressure is released large volumes of gas will be produced which form flammable mixtures with air over the range of approximately 2 % (V/V) to 10 % (V/V). This European Standard involves the sampling, handling and testing of LPG. All procedures should be conducted away from sources of ignition such as naked flames, unprotected electrical equipment and electrostatic hazards. Testing should be performed as far as practicable under an electrically-safe ventilation hood. LPG in liquid form can cause cold burns to the skin. Protective clothing such as gloves and goggles should be worn if contact with the skin is likely to occur. Unnecessary inhalation of LPG vapour should be avoided. The operator should not be exposed to atmospheres containing more than 1 800 mg/m3 over an 8 h time-weighted average (TWA) reference period, or more than 2 250 mg/m3 over a short term, 10 min reference period. One of the tests described in this European Standard involves the operator inhaling a mixture of air and LPG vapour. Particular attention is drawn to the cautionary statement provided in A.1, where this method is referred to.

EVS-EN 13352:2012
Hind 16,10 EUR
Specification for the performance of automatic tank contents gauges
This European Standard specifies the minimum performance requirements for various classes of automatic tank gauges which are limited to static tanks of shop fabricated manufacture both metallic and non metallic, underground and above ground which do not exceed 5 m in height. It is applicable to gauges for fuels (products) which are flammable, having a flash point up to but not exceeding 100 °C, stored at premises (e.g. filling stations) at which fuel is dispensed for use in vehicles and other forms of transportation. This European Standard applies to gauges suitable for use at ambient temperatures and subject to normal operational pressure variations. Gauging of liquefied gases are not covered by this standard. This European Standard relates to the measurement of product level, measurement of product temperature and detection of the presence of free water. The detection of free water may be compromised for Alcohol blended fuels.

EVS-EN 13617-2:2012
Hind 10,90 EUR
Bensiinijaamad. Osa 2: Ohutusnõuded mõõtepumpadel ja tankuritel kasutamiseks mõeldud kaitselülitite valmistamisele ja jõudlusele
This European Standard specifies safety requirements for the construction and performance of safe breaks to be fitted to metering pumps and dispensers installed at filling stations and used to dispense liquid fuels into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l min-1. The requirements apply to safe breaks at ambient temperatures from –20 °C to +40 °C with the possibility for an extended temperature range. It pays particular attention to electrical, mechanical and hydraulic characteristics of, and electrical apparatus incorporated within or mounted on, the safe break. This European Standard applies mainly to hazards related to the ignition of liquid fuels being dispensed or their vapour. This European Standard also addresses electrical and mechanical hazards.

EVS-EN 13617-3:2012
Hind 10,19 EUR
Bensiinijaamad. Osa 3: Ohutusnõuded sulgurventiilide valmistamisele ja jõudlusele
This European Standard specifies safety and environmental requirements for the construction and performance of shear valves to be fitted to metering pumps, dispensers, and/or satellite delivery systems installed at petrol filling stations and used to dispense liquid fuels into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l min-1. The requirements apply to shear valves at ambient temperatures from –20 °C to +40 °C with the possibility for an extended temperature range. It pays particular attention to mechanical and hydraulic characteristics.

EVS-EN 13617-4:2012
Hind 8,72 EUR
Bensiinijaamad. Osa 4: Ohutus- ja keskkonnanõuded mõõtepumpadel ja tankuritel kasutamiseks mõeldud pöördpumpade valmistamisele ja jõudlusele
This European Standard specifies safety requirements for the construction and performance of swivels to be fitted to delivery hose assemblies on metering pumps and dispensers installed at filling stations and used to dispense liquid fuels into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l min-1. It pays particular attention to electrical, mechanical and hydraulic characteristics of swivels. The requirements apply to swivels at ambient temperatures from –20 °C to +40 °C with the possibility for an extended temperature range. This European Standard applies mainly to hazards related to the ignition of liquid fuels being dispensed or their vapour. This European Standard also addresses electrical and mechanical hazards of swivels. This European Standard is not applicable to swivels for the dispensing of any compressed ga

CEN/TR 16366:2012
Hind 11,67 EUR
Liquid petroleum products - Middle distillates and fatty acid methyl ester (FAME) fuels and blends - Round Robin report on applicability of Rapid Small Scale Oxidation Test method
This Technical Report describes a series of round robin test campaigns for precision estimation of EN 16091. Furthermore, this document includes a summary of the results of the RRTs (see Clause 7 and Annex B).

EVS-EN 15415-2:2012
Hind 8,01 EUR
Solid recovered fuels - Determination of particle size distribution - Part 2: Maximum projected length method (manual) for large dimension particles
This European Standard specifies the determination of particle size distribution of solid recovered fuels. It establishes a manual method for the determination of the maximum projected length for large dimension particles. It applies to both agglomerated and non-agglomerated solid recovered fuel pieces exhibiting an irregular shape, such as shredded end-of-life tyres and demolition woods. This document does not apply to filaments protruding from the SRF pieces.

EVS-EN 15415-3:2012
Hind 8,72 EUR
Solid recovered fuels - Determination of particle size distribution - Part 3: Method by image analysis for large dimension particles
This European Standard specifies the determination of particle size distribution of solid recovered fuels using an image analysis method. It applies to both agglomerated and non-agglomerated solid, recovered, fuel pieces exhibiting an irregular shape, such as shredded end-of-life tyres and demolition woods. It provides the determination of the maximum projected length as well as parameters such as equivalent diameter. It also gives a characterisation of the filaments protruding from the SRF pieces.

EVS-EN ISO 13032:2012
Hind 9,49 EUR
Petroleum products - Determination of low concentration of sulfur in automotive fuels - Energy-dispersive X-ray fluorescence spectrometric method (ISO 13032:2012)
This International Standard specifies an energy dispersive X‑ray fluorescence (EDXRF) test method for the determination of sulfur content in automotive gasoline containing up to 3,7 % (m/m) oxygen [including those blended with ethanol up to 10 % (V/V)], and in diesel fuels [including those containing up to about 10 % (V/V) fatty acid methylester (FAME)] having sulfur contents in the range 8 mg/kg to 50 mg/kg. Other products can be analysed and other sulfur contents can be determined according to this test method; however, no precision data for products other than automotive fuels and for results outside the specified range have been established for this International Standard. For reasons of spectral overlap, this International Standard is not applicable to leaded automotive gasoline, gasoline having a content of greater than 8 mg/kg lead replacement or to product and feedstock containing lead, silicon, phosphorus, calcium, potassium or halides at concentrations greater than one tenth of the concentration of sulfur measured or more than 10 mg/kg, whichever is the greater.

Asendatud või tühistatud standardid

EVS-EN 589:2008
Mootorikütused. Vedelgaas. Nõuded ja katsemeetodid
Käesolev standard sätestab nõuded ja katsemeetodid turustatavale ja tarnitavale mootorikütusena kasutatavale vedelgaasile LPG (Liquefied Petroleum Gas). See on rakendatav mootorikütusena kasutatavale vedelgaasile, mida kasutatakse mootorikütusena vedelgaasi jaoks kohandatud mootoriga veokites.
This European Standard specifies requirements and test methods for marketed and delivered automotive LPG (Liquefied Petroleum Gas). It is applicable to automotive LPG for use in LPG engine vehicles designed to run on automotive LPG.
Keel: Eesti, Inglise

EVS-EN 13617-2:2004
Bensiinijaamad. Osa 2: Ohutusnõuded mõõtepumpadel ja tankuritel kasutamiseks mõeldud kaitselülitite valmistamisele ja jõudlusele
This European Standard specifies safety requirements for the construction and performance of safe breaks to be fitted to metering pumps and dispensers installed at filling stations and used to dispense liquid fuels into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l×min-1. It pays particular attention to electrical, mechanical and hydraulic characteristics of, and electrical apparatus incorporated within or mounted on, the safe break.
Keel: Inglise

EVS-EN 13617-4:2004
Bensiinijaamad. Osa 4: Ohutus- ja keskkonnanõuded mõõtepumpadel ja tankuritel kasutamiseks mõeldud pöördpumpade valmistamisele ja jõudlusele
This European Standard specifies safety requirements for the construction and performance of swivels to be fitted to delivery hose assemblies on metering pumps and dispensers installed at filling stations and used to dispense liquid fuels into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l×min-1. It pays particular attention to electrical, mechanical and hydraulic characteristics of swivels.
Keel: Inglise

EVS-EN 13352:2002
Specification for the performance of automatic tank contents gauges
This European Standard specifies the minimum performance requirements for various classes of automatic tank contents gauges which are limited to static tanks of shop fabricated manufacture both metallic and non metallic, underground and above ground which do not exceed 100 000 l in capacity or 5 m in height
Keel: Inglise

EVS-EN 13617-3:2004
Bensiinijaamad. Osa 3: Ohutusnõuded sulgurventiilide valmistamisele ja jõudlusele
This European Standard specifies safety and environmental requirements for the construction and performance of shear valves to be fitted to metering pumps, dispensers, and/or satellite delivery systems installed at petrol filling stations and used to dispense liquid fuels into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l×min-1. It pays particular attention to mechanical and hydraulic characteristics.
Keel: Inglise

Kavandite arvamusküsitlus

prEN 16423
Tähtaeg 30.06.2012
Liquefied petroleum gases - Determination of dissolved residue - Gas chromatographic method using liquid, on-column injection
This European Standard specifies a method for the determination of the dissolved residual matter, also known as evaporation residue, in liquefied petroleum gases (LPG), by gas chromatography in the range of (10 to 600) mg/kg (ppm mass). This test method quantifies soluble organic compounds (hydrocarbon materials), sometimes called ‘evaporation residue’, which can be present in liquefied petroleum gases and which are substantially less volatile than the LPG product, i.e. with a boiling point between 174 °C and 522 °C (C10 to C40). Higher boiling materials, or materials that adhere permanently to the chromatographic column, will not be detected. WARNING - This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Keel: Inglise

prEN 12597
Tähtaeg 30.06.2012
Bituumen ja bituumensideained. Terminoloogia
This European Standard defines terms for paving grade or industrial bitumen of various types and binders derived from bitumen. This standard is intended to cover materials only within the scope of CEN/TC 336, i.e. only bitumens and bituminous binders. It should consequently not extend to non-petroleum “hydrocarbon” binders such as coal tar and its derivatives or to natural asphalts. However, some definitions are given for some excluded materials and related terms. The corresponding terms were introduced only when they appeared in a definition of a product or process and when their definition was found necessary for understanding or for avoiding any ambiguity.
Keel: Inglise

EN ISO 19902:2008/prA1
Tähtaeg 30.06.2012
Petroleum and natural gas industries - Fixed steel offshore structures (ISO 19902:2007/DAM 1:2012)
This International Standard specifies requirements and provides recommendations applicable to the following types of fixed steel offshore structures for the petroleum and natural gas industries: - caissons, free-standing and braced; - jackets; - monotowers; - towers. In addition, it is applicable to compliant bottom founded structures, steel gravity structures, jack-ups, other-bottom founded structures and other structures related to offshore structures (such as underwater oil storage-tanks, bridges and connecting structures), to the extent to which its requirements are relevant.
Keel: Inglise