77 METALLURGIA

Tagasi peagrupi juurde

Uued standardid

EVS-EN 10169:2010+A1:2012
Hind 15,40 EUR
Continuously organic coated (coil coated) steel flat products - Technical delivery conditions CONSOLIDATED TEXT
This European Standard specifies requirements for continuously organic coated (coil coated) steel flat products. It particularly specifies the performance requirements. The products covered are wide strip, sheet cut from wide strip, slit wide strip, strip rolled in widths less than 600 mm and cut lengths (from sheet or strip). NOTE This document is not applicable to continuously organic coated flat products made of: - tinmill products, - electrical steels.

Asendatud või tühistatud standardid

EVS-EN 15205:2007
Determination of hexavalent chromium in corrosion protection layers - Qualitative analysis
This document describes the testing method for the qualitative analysis of hexavalent chrome in corrosion protection layers.
This document describes the testing method for the qualitative analysis of hexavalent chromium in corrosion protection layers.
Keel: Inglise

EVS-EN 10169:2010
Continuously organic coated (coil coated) steel flat products - Technical delivery conditions
This European Standard specifies requirements for continuously organic coated (coil coated) steel flat products. It particularly specifies the performance requirements. The products covered are wide strip, sheet cut from wide strip, slit wide strip, strip rolled in widths less than 600 mm and cut lengths (from sheet or strip).
Keel: Inglise

Kavandite arvamusküsitlus

FprEN 12450
Tähtaeg 30.06.2012
Copper and copper alloys - Seamless, round copper capillary tubes
This European Standard specifies the composition, property requirements and tolerances on dimensions and on form for seamless round copper capillary tubes for use as metering lines for liquids or gases where close controls over the smoothness and dimensions of the bore are required to ensure uniform flow characteristics. This European Standard applies to capillary tubes in straight lengths, or in coils, in the size range up to and including 6,10 mm outside diameter and from 0,30 mm up to and including 4,45 mm inside diameter which are intended for restrictor applications. The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.
Keel: Inglise

FprEN 62483
Tähtaeg 30.06.2012
Environmental acceptance requirements for tin whisker susceptibility of tin and tin alloy surface finishes
The methodology described in this document is applicable for environmental acceptance testing of tin based surface finishes and mitigation practices for tin whiskers. This methodology may not be sufficient for applications with special requirements, (i.e. military, aerospace, etc.). Additional requirements may be specified in the appropriate requirements (procurement) documentation. This specification does not apply to components with bottom-only terminations where the full plated surface is wetted during assembly (for example: quad flat no leads and ball grid array components, flip chip bump terminations). Adherence to this standard shall include meeting the reporting requirements described in Clause 6
Keel: Inglise

prEN ISO 14577-1
Tähtaeg 30.06.2012
Metallic materials - Instrumented indentation test for hardness and materials parameters - Part 1: Test method (ISO/DIS 14577-1:2012)
This part of ISO 14577 specifies the method of instrumented indentation test for determination of hardness and other materials parameters for the three ranges given in Table 1. The macro and micro ranges are distinguished by the test forces in relation to the indentation depth. Attention is drawn to the fact that the micro range has an upper limit given by the test force (2 N) and a lower limit given by the indentation depth of 0,2 μm. The determination of hardness and other materials parameters is given in Annex A. At high contact pressures, damage to the indenter is possible. For this reason in the macro range, hardmetal indenters are often used. For test pieces with very high hardness and modulus of elasticity permanent indenter deformation may occur and this should be detected using suitable reference materials and its influence on the test result shall be taken into account.
Keel: Inglise

prEN ISO 14577-2
Tähtaeg 30.06.2012
Metallic materials - Instrumented indentation test for hardness and materials parameters - Part 2: Verification and calibration of testing machines (ISO/DIS 14577-2:2012)
This part of ISO 14577 specifies the method of verification and calibration of testing machines for carrying out the instrumented indentation test in accordance with ISO/DIS 14577-1:2012. It describes a direct verification method for checking the main functions of the testing machine and an indirect verification method suitable for the determination of the repeatability of the testing machine. The indirect method shall be used in addition to the direct method and for the periodic routine checking of the testing machine in service. The indirect method of verification of the testing machine shall be carried out independently for each test method. This part of ISO 14577 is also applicable for transportable testing machines.
Keel: Inglise

prEN ISO 14577-3
Tähtaeg 30.06.2012
Metallic materials - Instrumented indentation test for hardness and materials parameters - Part 3: Calibration of reference blocks (ISO/DIS 14577-3:2012)
This part of ISO 14577 specifies a method for the calibration of reference blocks to be used for the indirect verification of testing machines for the instrumented indentation test, as specified in ISO/DIS 14577-2:2012.
Keel: Inglise

FprEN ISO 13944
Tähtaeg 30.06.2012
Lubricated metal-powder mixes - Determination of lubricant content - Soxhlet extraction method (ISO/FDIS 13944:2012)
This International Standard specifies a method for the determination of the lubricant content of a powder mix. The method is also suitable for preparing samples for measuring the content of elements, e.g. graphite and oxygen, the determination of which is interfered with by the presence of a lubricant. A condition of the application of the method is that a suitable solvent for the lubricant concerned is known and available.
Keel: Inglise

prEN ISO 377
Tähtaeg 30.06.2012
Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO/DIS 377:2012)
This International Standard specifies requirements for the identification, location and preparation of samples and test pieces intended for mechanical tests on steel sections, bars, rod, flat products and tubular products as defined in ISO 6929. If agreed in the order this standard may also apply to other metallic products. These samples and test pieces are for use in tests which are carried out in conformity with the methods specified in the product or material standard or, in the absence of this, in the test standard. Where the requirements of the order or product standard differ from those given in this International Standard, then the requirements of the order or product standard apply.
Keel: Inglise