91 EHITUSMATERJALID JA EHITUS
Tagasi peagrupi juurde
Uued standardid
EVS-EN 14617-6:2012
Hind 6,47 EUR
Identne EN 14617-6:2012
Agglomerated stone - Test methods - Part 6: Determination of thermal shock resistance
This European Standard specifies a method to assess possible modifications of agglomerated stones under the effect of sudden changes in temperature (thermal shock) by immersion in hot water.
EVS-EN 14617-4:2012
Hind 7,38 EUR
Identne EN 14617-4:2012
Agglomerated stone - Test methods - Part 4: Determination of the abrasion resistance
This European Standard specifies a method for determining the abrasion resistance of agglomerated stone products.
EVS-EN 14617-5:2012
Hind 6,47 EUR
Identne EN 14617-5:2012
Agglomerated stone - Test methods - Part 5: Determination of freeze and thaw resistance
This European Standard specifies a method to assess the effect of freeze/thaw cycles on agglomerated stones. It contains provisions for a technological test to be carried out to assess the effect of freeze/thaw cycles on the flexural strength characteristics of the stone.
EVS-EN 14617-10:2012
Hind 8,01 EUR
Identne EN 14617-10:2012
Agglomerated stone - Test methods - Part 10: Determination of chemical resistance
This European Standard specifies a method for determining the chemical resistance and the resistance to stains of agglomerated stones (see EN 14618) with a polished surface after a prolonged contact with chemical materials.
EVS-EN 14825:2012
Hind 20,74 EUR
Identne EN 14825:2012
Air conditioners, liquid chilling packages and heat pumps, with electrically driven compressors, for space heating and cooling - Testing and rating at part load conditions and calculation of seasonal performance
This European Standard covers air conditioners, heat pumps and liquid chilling packages. It applies to factory made units defined in EN 14511-1:2011, except single duct, control cabinet and close control units. This European Standard gives the calculation methods for the determination of reference seasonal energy efficiency SEER and SEERon and reference seasonal coefficient of performance SCOP, SCOPon and SCOPnet. Such calculation methods may be based on calculated or measured values. In case of measured values, this European Standard covers the test methods for determination of capacities, EER and COP values during active mode at part load conditions. It also covers test methods for electric power consumption during thermostat off mode, standby mode and crankcase heater mode. This European Standard serves as an input for the calculation of the system energy efficiency in heating mode of specific heat pump systems in buildings, as stipulated in the standard EN 15316-4-2.
EVS-EN 1024:2012
Hind 10,19 EUR
Identne EN 1024:2012
Tükk-kattena paigaldatavad savikatusekivid -Geomeetriliste näitajate määramine
This European standard specifies the methods for determining the geometric characteristics of clay tiles as defined in EN 1304, Clay roofing tiles and fittings Product definitions and specifications.
CEN/TR 16349:2012
Hind 7,38 EUR
Framework for a specification on the avoidance of a damaging Alkali-Silica Reaction (ASR) in concrete
This Technical Report gives guidance for avoiding a damaging Alkali-Silica Reaction (ASR) in concrete.
EVS-EN 14617-12:2012
Hind 8,01 EUR
Identne EN 14617-12:2012
Agglomerated stone - Test methods - Part 12: Determination of dimensional stability
This European Standard specifies the test method to be used for the determination of the dimensional stability and warping of agglomerated stones when in contact with water. This European Standard applies to agglomerated stones to be installed by adhesive on walls and floors. The test is mainly performed to classify the material according to the degree of sensitivity to water and to select a suitable adhesive for the correct laying of agglomerated stones.
EVS-EN 779:2012
Hind 19,05 EUR
Identne EN 779:2012
Particulate air filters for general ventilation - Determination of the filtration performance
This European Standard refers to particulate air filters for general ventilation. These filters are classified according to their performance as measured in this test procedure. This European Standard contains requirements to be met by particulate air filters. It describes testing methods and the test rig for measuring filter performance. In order to obtain results for comparison and classification purposes, particulate air filters shall be tested against two synthetic aerosols, a fine aerosol for measurement of filtration efficiency as a function of particle size within a particle size range 0,2 m to 3,0 m, and a coarse one for obtaining information about test dust capacity and, in the case of coarse filters, filtration efficiency with respect to coarse loading dust (arrestance). This European Standard applies to air filters having an initial efficiency of less than 98 % with respect to 0,4 μm particles. Filters shall be tested at an air flow rate between 0,24 m3/s (850 m3/h) and 1,5 m3/s (5400 m3/h). The performance results obtained in accordance with this standard cannot by themselves be quantitatively applied to predict performance in service with regard to efficiency and lifetime. Other factors influencing performance to be taken into account are described in Annex A (informative).
EVS-EN 1745:2012
Hind 20,74 EUR
Identne EN 1745:2012
Masonry and masonry products - Methods for determining thermal properties
This European Standard specifies procedures for the determination of thermal properties of masonry and masonry products.
EVS-EN 1467:2012
Hind 9,49 EUR
Identne EN 1467:2012
Natural stones - Rough blocks - Requirements
This European Standard specifies requirements for rough blocks of natural stone from which products for use in building or commemorative stones and other similar applications are made. It does not cover artificially agglomerated stony material nor installation.
EVS-EN 1468:2012
Hind 9,49 EUR
Identne EN 1468:2012
Natural stone - Rough slabs - Requirements
This European Standard specifies requirements for rough slabs of natural stone from which products for use in buildings or commemorative stones and other similar applications are made. It does not cover artificially agglomerated stony material nor installation.
IEC 60364-7-709:2012
Hind 98,72 EUR
Low-voltage electrical installations - Part 7-709: Requirements for special installations or locations - Marinas and similar locations
IEC 60364-7-709:2007+A1:2012 applies only to circuits intended to supply pleasure craft or houseboats in marinas and similar locations. The particular requirements do not apply to the supply of house boats if they are directly supplied from the public network. The particular requirements do not apply to the internal electrical installations of pleasure craft or house boats. For the remainder of the electrical installation of marinas and similar locations the general requirements of IEC 60364 together with the relevant particular requirements of IEC 60364-7 apply. This second edition of IEC 60364-7-709 cancels and replaces the first edition, published in 1994. It constitutes a technical revision. The major changes with regard to the previous edition concern are the removal of the requirements for the electrical installation in pleasure craft (these are now covered by IEC 60092-507) and the alignment of the requirements with those in other parts of IEC 60364. This consolidated versio
IEC 60335-2-67:2012
Hind 180,98 EUR
Household and similar electrical appliances - Safety - Part 2-67: Particular requirements for floor treatment machines, for commercial use
IEC 60335-2-67:2012 deals with the safety of powered floor treatment machines intended for commercial indoor or outdoor use for the following applications:
- scrubbing,
- wet or dry pick-up,
- polishing and dry buffing,
- application of wax, sealing products and powder based detergents,
- shampooing,
- stripping, grinding and scarifying of floors with an artificial surface. Their cleaning motion is more lateral or periodic than linear. This standard applies to machines for commercial use. The following list, although not comprehensive, gives an indication of locations that are included in the scope:
- public use areas such as hotels, schools, hospitals;
- industrial locations, for example factories and manufacturing shops;
- retail outlets, for example shops and supermarkets;
- business premises, for example offices and banks;
- all uses other than normal housekeeping purposes.
They are not equipped with a traction
EVS-EN 62059-32-1:2012
Hind 9,49 EUR
Electricity metering equipment - Dependability - Part 32-1: Durability - Testing of the stability of metrological characteristics by applying elevated temperature
The stability of metrological characteristics is one important aspect of durability. This part of IEC 62059 specifies a method for testing the stability of metrological characteristics of electricity meters, by operating a test specimen at the upper limit of the specified operating range of temperature, voltage and current for an extended period. Functional performance other than the accuracy of energy measurement is out of the scope of this standard. Note, that from the results of this test, no conclusion can be drawn for the length of period during which the stability of the metrological characteristics will be maintained when the meter is operated under usual conditions. This International Standard is applicable to all types of electricity meters in the scope of IEC TC 13.
EVS-EN 62561-7:2012
Hind 9,49 EUR
Lightning Protection System Components (LPSC) - Part 7: Requirements for earthing enhancing compounds
This Part 7 of IEC 62561 specifies the requirements and tests for earthing enhancing compounds producing low resistance of an earth termination system.
EVS-EN 62337:2012
Hind 15,40 EUR
Commissioning of electrical, instrumentation and control systems in the process industry - Specific phases and milestones
This International Standard defines specific phases and milestones (see Figure 1) in the commissioning of electrical, instrumentation and control systems in the process industry. By way of example, it describes activities following the “completion-of-erection” milestone of the project and prior to the “acceptance-of-the-plant” phase by the owner. Such activities need to be adapted for each type of process/plant concerned.
ISO 11855-5:2012
Hind 54,29 EUR
Building environment design -- Design , dimensioning, installation and control of embedded radiant heating and cooling systems -- Part 5: Installation
EVS-EN ISO 13791:2012
Hind 23,62 EUR
Thermal performance of buildings - Calculation of internal temperatures of a room in summer without mechanical cooling - General criteria and validation procedures (ISO 13791:2012)
This International Standard specifies the assumptions, boundary conditions, equations and validation tests for a calculation procedure, under transient hourly conditions, of the internal temperatures (air and operative) during warm periods, of a single room without any cooling/heating equipment in operation. No specific numerical techniques are imposed by this International Standard. Validation tests are included in Clause 8. An example of a solution technique is given in Annex A. This International Standard does not contain sufficient information for defining a procedure able to determine the internal conditions of special zones such as attached sun spaces, atria, indirect passive solar components (trombe walls, solar panels) and zones in which the solar radiation may pass through the room. For such situations different assumptions and more detailed solution models are needed (see Bibliography).
EVS-EN ISO 13792:2012
Hind 18,00 EUR
Thermal performance of buildings - Calculation of internal temperatures of a room in summer without mechanical cooling - Simplified methods (ISO 13792:2012)
This International Standard specifies the required input data for simplified calculation methods for determining the maximum, average and minimum daily values of the operative temperature of a room in warm periods: - to define the characteristics of a room at the design stage in order to avoid overheating in summer; - to define whether the installation of a cooling system is necessary or not. Clause 6 gives the criteria to be met by a calculation method in order to satisfy this International Standard.
Asendatud või tühistatud standardid
EVS-EN 1024:1999
Identne EN 1024:1997
Tükk-kattena paigaldatavad savikatusekivid -Geomeetriliste näitajate määramine
See Euroopa stnadard esitab meetodid savikatusekivide geomeetriliste näitajate määramiseks, nagu on defineeritud standardis EN 1304
Keel: Inglise
EVS-EN 1745:2002
Identne EN 1745:2002
Müüritis ja müüritisetooted. Arvutuslike soojusväärtuste määramise meetodid
Käesolev Euroopa standard esitab meetodid müüritise ja müüritoodete arvutuslike soojusväärtuste (soojustakistuse ja/või soojuserijuhtivuse) määramiseks.
This European Standard gives procedures for the determination of design thermal values (thermal resistance and/or thermal conductivity) of masonry and masonry products.
Keel: Eesti, Inglise
EVS-EN 14617-12:2005
Identne EN 14617-12:2005
Agglomerated stone - Test methods - Part 12: Determination of dimensional stability
This European standard specifies a test method to determine the dimensional stability, intended as the evaluation of a deformation, towards a bearing plane, by prolonged contact with water, of agglomerated stones tiles used for flooring and cladding in building. The test is mainly performed to select a suitable adhesive for the laying down operations.
Keel: Inglise
EVS-EN 12977-3:2008
Identne EN 12977-3:2008
Thermal solar systems and components - Custom built systems - Part 3: Performance test methods for solar water heater stores
This European Standard specifies test methods for the performance characterization of stores which are intended for use in small custom built systems as specified in prCEN/TS 12977-1. Stores tested according to this document are commonly used in solar hot water systems. However, also the thermal performance of all other thermal stores with water as storage medium can be assessed according to the test methods specified in this document. The document applies to stores with a nominal volume between 50 l and 3 000 l. This document does not apply to combistores. Performance test methods for solar combistores are specified in prCEN/TS 12977-4.
Keel: Inglise
EVS-EN 14617-4:2005
Identne EN 14617-4:2005
Agglomerated stone - Test methods - Part 4: Determination of the abrasion resistance
This European standard specifies a method for determining the abrasion resistance of agglomerated stone products
Keel: Inglise
EVS-EN 14617-10:2005
Identne EN 14617-10:2005
Agglomerated stone - Test methods - Part 10: Determination of chemical resistance
This European standard specifies a method for determination of the chemical resistance and the resistance to stains of agglomerated stones (see prEN 14618) with polished surface after a prolonged contact with chemical materials
Keel: Inglise
EVS-EN 1468:2004
Identne EN 1468:2003
Natural stone - Rough slabs - Requirements
This European Standard specifies requirements for rough slabs of natural stone from which products for use in buildings or commemorative stones and other similar applications are made. It does not cover artificially agglomerated stony material and does not cover installation
Keel: Inglise
EVS-EN 14617-6:2005
Identne EN 14617-6:2005
Agglomerated stone - Test methods - Part 6: Determination of thermal shock resistance
This European Standard specifies a method to assess possible modifications of agglomerated stones under the effect of sudden changes in temperature (thermal shock) by immersion in hot water
Keel: Inglise
EVS-EN 779:2003
Identne EN 779:2002
Particulate air filters for general ventilation - Determination of the filtration performance
This European Standard refers to particulate air filters for general ventilation. These filters are classified according to their performance as measured in this test procedure. This European Standard contains requirements to be met by particulate air filters. It describes testing methods and the test rig for measuring filter performance
Keel: Inglise
EVS-EN 14617-5:2005
Identne EN 14617-5:2005
Agglomerated stone - Test methods - Part 5: Determination of freeze and thaw resistance
The European Standard specifies a method to assess the effect of freeze/thaw cycles on agglomerated stones. The standard contains provision for technological test to assess the effect of freeze/thaw cycles on the flexural strength characteristic
Keel: Inglise
EVS-EN 50379-3:2004
Identne EN 50379-3:2004
Specification for portable electrical apparatus designed to measure combusion flue gas parameters of heating appliances - Part 3: Performance requirements for apparatus used in non-statutory servicing of gas fired heating appliances
This European Standard covers apparatus designed for checking the performance of heating appliances by measuring flue gas parameters of gas fired heating appliances for domestic residential and commercial applications. The apparatus may consist of different functional modules which may be tested separately for complying with this standard, and will be combined in different ways according to the different applications. The apparatus shall comply with the general requirements as specified in EN 50379-1 and the performance requirements of EN 50379-3.
Keel: Inglise
EVS-EN 50164-7:2008
Identne EN 50164-7:2008
Lightning Protection Components (LPC) -- Part 7: Requirements for earthing enhancing compounds
This European Standard specifies the requirements and tests for – earthing enhancing compounds increasing the contact surface area of the earth electrode.
Keel: Inglise
EVS-EN 50379-2:2004
Identne EN 50379-2:2004
Specification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances Part 2: Performance requirements for apparatus used in statutory inspections and assessment
This European Standard covers apparatus designed to measure flue gas parameters of heating appliances for domestic residential and commercial applications using commercially available fuels in compliance with metrological specification.
Keel: Inglise
EVS-EN 1467:2004
Identne EN 1467:2003
Natural stone - Rough blocks - Specifications
This European Standard specifies requirements for rough blocks of natural stone from which products for use in building or commemorative stones and other similar applications are made. It does not cover artificially agglomerated stony material and does not cover installation
Keel: Inglise
EVS-EN ISO 13791:2005
Thermal performance of buildings - Calculation of internal temperatures of a room in summer without mechanical cooling - General criteria and validation procedures
This European Standard specifies the assumptions, boundary conditions, equations and validation tests for a calculation procedure, under transient hourly conditions, of the internal temperatures (air and operative) during the warm period, of a single room without any cooling/heating equipment in operation. No specific numerical techniques are imposed by this standard. Validation tests are included in clause 7. An example of a solution technique is given in annex A.
Keel: Inglise
EVS-EN ISO 13792:2005
Thermal performance of buildings - Calculation of internal temperatures of a room in summer without mechanical cooling - Simplified methods
This document specifies the required input data for simplified calculation methods for determining the maximum,average and minimum daily values of the operative temperature of a room in the warm period:a) to define the characteristics of a room in order to avoid overheating in summer at the design stage; b) to define whether the installation of a cooling system is necessary or not.
Keel: Inglise
IEC 60335-2-67:2005
Household and similar electrical appliances - Safety - Part 2-67: Particular requirements for floor treatment and floor cleaning machines, for industrial and commercial use
This consolidated version consists of the third edition (2002) and its amendment 1 (2005). Therefore, no need to order amendment in addition to this publication.
Keel: Inglise
IEC 60335-2-67/Amd 1:2005
Amendment 1 - Household and similar electrical appliances - Safety - Part 2-67: Particular requirements for floor treatment and floor cleaning machines, for industrial and commercial use
Keel: Inglise
Kavandite arvamusküsitlus
prEN 14076
Identne prEN 14076 rev:2012
Tähtaeg 30.06.2012
Puittrepid. Terminoloogia
This European Standard defines general terms relating to timber stairs or to timber in prefabricated stairs, including wood-based materials for dwellings and buildings other than dwellings for permanent use
Keel: Inglise
FprEN 1013
Identne FprEN 1013:2012
Tähtaeg 30.06.2012
Light transmitting single skin profiled plastics sheets for internal and external roofs, walls and ceilings - Requirements and test methods
This European Standard specifies the requirements for light transmitting single skin profiled plastics sheets for internal and external walls, roofs and ceilings. It is applicable to single skin sheets which are used as a single layer or when assembled to form multiple layer construction. It also specifies the test methods and provides for the evaluation of conformity and marking of the sheets.
Keel: Inglise
FprEN 15684
Identne FprEN 15684:2012
Tähtaeg 30.06.2012
Building hardware - Mechatronic cylinders - Requirements and test methods
This European Standard specifies requirements for performance and testing of Mechatronic Cylinders and their keys and/or electronic keys. It applies to cylinders for such locks designed to be normally used in buildings. It also applies to cylinders for use with other hardware products such as exit devices, door operators, etc. or monitoring facilities and alarm systems. It establishes categories of use based on performance tests and grades of security based on design requirements and on performance tests that simulate attack. This European standard includes assessment of additional features when they are included in the cylinder design. This European standard does not cover any other element of a security system, other than those directly involved in the control of a cylinder. The suitability of cylinders for use on fire or smoke-door assemblies is determined by fire performance tests conducted in addition to the performance testing specified by this European standard; see Annex A.
Keel: Inglise
prEN 12390-13
Identne prEN 12390-13:2012
Tähtaeg 30.06.2012
Testing hardened concrete - Part 13: Determination of secant modulus of elasticity in compression
This standard specifies the procedure for the determination of the secant modulus of elasticity in compression of hardened concrete on test specimens which may be cast or taken from a structure.
Keel: Inglise
prEN 16416
Identne prEN 16416:2012
Tähtaeg 30.06.2012
Geosynthetic clay barriers - Determination of water flux index - Flexible wall permeameter method at constant head
This European Standard describes an index test method that covers laboratory measurement of water flux through saturated geosynthetic clay barrier (GBR-C) specimens using a flexible wall permeameter at constant head. This test method is applicable to GBR-C products with no additional sealing layers attached. This test method provides a measurement of flux under a prescribed set of conditions that can be used for manufacturing quality control. The test method can also be used to check conformance. The flux value determined using this test method is not considered to be representative of the in-service flux of a GBR-C.
Keel: Inglise
prEN 16433
Identne prEN 16433:2012
Tähtaeg 30.06.2012
Internal blinds - Protection from strangulation hazards - Test methods
This European Standard specifies test methods for the verification of the requirements relating to the protection from strangulation as specified in EN 13120/prA1:2012. It applies to all internal blinds, whatever their design and the nature of the materials used, such as: - venetian blind: free hanging, guided, non-retractable; - roller blind: free hanging, side guided, with tensioned fabric; - vertical blind: free hanging, with top and bottom track, sloping headrail; - pleated and honeycomb blind: free hanging, guided, laterally moving, tensioned; - Roman Shades; - Austrian / Festoon blinds; - panel blinds; - plantation shutters; - roll-up blinds. This European Standard also applies to insect screens as specified in EN 13561 and to blinds in sealed glazed units. These products may be operated manually, with or without compensating springs, or by means of electric motors (power operated products).
Keel: Inglise
prEN 16434
Identne prEN 16434:2012
Tähtaeg 30.06.2012
Internal blinds - Protection from strangulation hazards - Requirements and Test methods for safety devices
This European Standard specifies requirements and test methods for safety devices to be used for protection from strangulation in internal blinds as specified in EN 13120 and insect screens as specified in EN 13561. These devices might be fitted to internal blinds and insect screens at the time of manufacture or for retrofitting. Safety devices covered include the following: - Tensioning devices; - Breakaway devices; - Accumulation devices; - Non tangling devices; - Inner cord stops. NOTE Although at the time this standard has been published, no product standard exists for draperies, requirements and test methods specified in the present standard might be applied to safety devices used in such products. For clarification purpose, the term “internal blinds” used in the present standard should mean “internal blinds and insect screens”.
Keel: Inglise
EN 13120:2009/prA1
Identne EN 13120:2009/prA1:2012
Tähtaeg 30.06.2012
Rulood sisekasutuses. Nõuded jõudlusele ja ohutusele
This European Standard specifies the requirements which internal blinds shall fulfil when fitted to a building. It deals also with the significant machinery hazards relating to construction, transport, installation, operation and maintenance of the internal blinds (see list of significant hazards in Annex B). It applies to the internal blinds, whatever their design and nature of the materials used, as listed below: - venetian internal blind: free hanging, guided, non-retractable; - roller internal blind: free hanging, side guided, with tensioned fabric; - vertical internal blind: free hanging, with top and bottom track, and sloping headrail; - pleated internal blind: free hanging and guided. These products may be operated manually, with or without compensating springs, or by means of electric motors (power operated products). This standard does not apply to Roman Shades, Austrian, Festoon, Pinoleum, laterally moving pleated internal blinds, insect screens or internal blinds in sealed glazed units. Noise aspects are not treated in this standard because this is not considered a safety issue. This standard is not applicable to internal blinds which are manufactured before the date of publication of this standard.
This European Standard specifies the requirements which internal blinds shall fulfil when fitted to a building. It deals also with the significant machinery hazards relating to construction, transport, installation, operation and maintenance of the internal blinds (see list of significant hazards in Annex B). It applies to the internal blinds, whatever their design and nature of the materials used, as listed below: - venetian internal blind: free hanging, guided, non-retractable; - roller internal blind: free hanging, side guided, with tensioned fabric; - vertical internal blind: free hanging, with top and bottom track, and sloping headrail; - pleated internal blind: free hanging and guided. These products may be operated manually, with or without compensating springs, or by means of electric motors (power operated products). This standard does not apply to Roman Shades, Austrian, Festoon, Pinoleum, laterally moving pleated internal blinds, insect screens or internal blinds in sealed glazed units. Noise aspects are not treated in this standard because this is not considered a safety issue. This standard is not applicable to internal blinds which are manufactured before the date of publication of this standard.
Keel: Inglise
prEN 15091
Identne prEN 15091:2012
Tähtaeg 30.06.2012
Sanitary tapware - Electronic opening and closing sanitary tapware
The purpose of this European Standard is to define requirements for marking, identification, leaktightness, electrical and operational safety and mechanical resistance for sanitary tapware with opening and closing controlled electronically.
Keel: Inglise
prEN 12597
Identne prEN 12597:2012
Tähtaeg 30.06.2012
Bituumen ja bituumensideained. Terminoloogia
This European Standard defines terms for paving grade or industrial bitumen of various types and binders derived from bitumen. This standard is intended to cover materials only within the scope of CEN/TC 336, i.e. only bitumens and bituminous binders. It should consequently not extend to non-petroleum “hydrocarbon” binders such as coal tar and its derivatives or to natural asphalts. However, some definitions are given for some excluded materials and related terms. The corresponding terms were introduced only when they appeared in a definition of a product or process and when their definition was found necessary for understanding or for avoiding any ambiguity.
Keel: Inglise
EN 15814:2011/FprA1
Identne EN 15814:2011/FprA1:2012
Tähtaeg 30.06.2012
Paksud niiskusetõkkekihid polümeermodifitseeritud bituumenist. Määratlused ja nõuded
This European Standard specifies the definitions and requirements of prefabricated polymer modified bituminous thick coatings used for the waterproofing of below ground structures. It applies to both onecomponent and two-component products. These products can be used with or without inlay. This European Standard does not apply to products that are to be used for roof waterproofing.
Keel: Inglise
prEN 15269-5
Identne prEN 15269-5:2012
Tähtaeg 30.06.2012
Extended application of test results for fire resistance and/or smoke control for door, shutter and openable window assesmblies, including their elements of building hardware - Part 5: Fire resistance of hinged and pivoted metal framed glazed doorsets and openable windows
This Part of prEN 15269, which should be read in conjunction with prEN 15269-1, covers single and double leaf, hinged and pivoted metal framed, glazed doorsets or openable windows. This document prescribes the methodology for extending the application of test results obtained from test(s) conducted in accordance with EN 1634-1. Subject to the completion of the appropriate test or tests selected from those identified in Clause 4 the extended application may cover all or some of the following non-exhaustive list: - Integrity only (E), radiation (EW) or insulated (EI1 or EI2) classifications; - Doorsets and openable windows - Door / window leaf; - wall/ceiling fixed elements (frame/suspension system); - glazing and non-glazed panels in doorset and openable window - items of building hardware; - decorative finishes; - intumescent, smoke, draught or acoustic seals; - alternative supporting construction(s).
Keel: Inglise
prEN 16430-1
Identne prEN 16430-1:2012
Tähtaeg 30.06.2012
Fan assisted radiators, convectors and trench convectors - Part 1: Technical specifications and requirements
This European Standard defines the technical specifications and requirements of fan assisted radiators, convectors and trench convectors for permanent installation in central heating systems. This European Standard covers radiators and convectors fed with water or steam at temperatures below 120 °C, supplied by a remote heating source. This European Standard does not apply to discrete heating appliances. This European Standard also defines the additional common data that the manufacturer shall provide to the trade in order to ensure the correct application of the products. This European Standard applies to the testing of thermal output and cooling capacity of fan assisted radiators, convectors and trench convectors, i.e. - fan assisted radiators and convectors, provided the heater/cooler has a dedicated fan or fans, - trench convectors with and without fan(s), provided the fan(s) are dedicated, - ventilation radiators and convectors (only heating). This European Standard also applies for radiators and convectors according to EN 442-2 to determine their cooling capacity.
Keel: Inglise
prEN 16430-2
Identne prEN 16430-2:2012
Tähtaeg 30.06.2012
Fan assisted radiators, convectors and trench convectors - Part 2: Test method and rating for thermal output
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 442-2, Radiators and convectors - Part 2: Test methods and rating EN 636, Plywood – Specifications EN ISO/IEC 17025, General requirements for the competence of testing and calibration laboratories (ISO/IEC 17025)
Keel: Inglise
prEN 16430-3
Identne prEN 16430-3:2012
Tähtaeg 30.06.2012
Fan assisted radiators, convectors and trench convectors - Part 3: Test method and rating for cooling capacity
This European Standard applies to the testing of the cooling capacity with no condensation of fan assisted radiators, convectors and trench convectors, i.e. - fan assisted radiators and convectors, provided the heater has a dedicated fan or fans, - radiators and convectors without dedicated fan(s), - trench convectors with and without fan(s), provided the heater and the fan(s) are dedicated.
Keel: Inglise
prEN 13055
Identne prEN 13055:2012
Tähtaeg 30.06.2012
Lightweight aggregates for concrete, mortar, grout, bituminous mixtures, surface treatments and for unbound and bound applications
This European Standard specifies the properties of lightweight aggregates and fillers derived thereof obtained by processing natural or manufactured materials and mixtures of these aggregates for concrete, mortar and grout, bituminous mixtures and surface treatments and for unbound and hydraulically bound applications for construction works. This European Standard covers lightweight aggregates of mineral origin having particle densities not exceeding 2000 kg/m3 (2,000 Mg/m3) or loose bulk densities not exceeding 1200 kg/m3 (1,200 Mg/m3) including: a) natural lightweight aggregates; b) lightweight aggregates manufactured from natural materials; c) lightweight aggregates manufactured from by-products of industrial processes or from recycled materials; d) lightweight aggregates as by-products of industrial processes. A list of the source materials that have been considered and are within the scope of this standard is given in Annex A (normative). NOTE 1 Recycled aggregates from construction and demolition waste and Municipal Solid Waste Incinerator Bottom Ash (MIBA) are covered by standards EN 12620, EN 13043, EN 13139 and EN 13242. Some lightweight aggregates for specific applications are covered in separate European product standards (Annex B, normative). This standard incorporates a general requirement that aggregates shall not release any dangerous substances in excess of the maximum permitted levels specified in a relevant European Standard for the material or permitted in the national regulations of the member state of destination. NOTE 2 Requirements for the declaration of the potential of aggregates to release regulated dangerous substances are currently under development. Until such time as these are finalised attention should be paid to requirements at the place of use. This standard also specifies that a quality control system is in place for use in factory production control and it provides for the evaluation of conformity of the products to this European Standard. The requirements specified in this standard may not be equally relevant to all types of lightweight aggregates. For particular applications the requirements and tolerances can be adapted for the end use.
Keel: Inglise
HD 60364-5-51:2009/prAA
Identne HD 60364-5-51:2009/prAA:2012
Tähtaeg 30.06.2012
Ehitiste elektripaigaldised. Osa 5-51: Elektriseadmete valik ja paigaldamine. Üldjuhised
This part of HD 60364 deals with the selection of equipment and its erection. It provides common rules for compliance with measures of protection for safety, requirements for proper functioning for intended use of the installation, and requirements appropriate to the external influences foreseen.
Keel: Inglise
FprHD 60364-7-718:2012/prAA
Identne FprHD 60364-7-718:2010/prAA:201
Tähtaeg 30.06.2012
Low-voltage electrical installations - Part 7-718: Requirements for special installations or locations - Communal facilities and workplaces
This standard provides additional requirements for electrical installations applicable to communal facilities and workplaces. Requirements of other parts of the 7-7XX series of IEC 60364 are also applicable, if they are relevant to this part. Typical examples of communal facilities and workplaces are listed below: - Assembly halls, assembly rooms - Exhibition halls - Theatres, cinemas - Sport arenas - Sales areas – Restaurants - Hotels, guest houses, residential care homes – Schools - Enclosed car parks - Meeting places, swimming halls, airports, railway stations, high rise buildings - Workshops, factories and industrial plants Access routes and escape routes are part of the above mentiond examples. The necessity of providing safety services in special buildings and areas may be governed by national regulations which may contain more stringent requirements.
Keel: Inglise
EN ISO 12570:2000/prA1
Identne ISO 12570:2000/DAM 1:2012
ja identne
EN ISO 12570:2000/prA1:2012
Tähtaeg 30.06.2012
Hygrothermal performance of building materials and products - Determination of moisture content by drying at elevated temperature - Amendment 1 (ISO 12570:2000/DAM 1:2012)
This standard, which is applicable to porous water permeable materials, specifies a general method for determining the free water content of building materials by drying at elevated temperature. The standard does not specify the method for sampling.
Keel: Inglise
FprEN ISO 16484-5
Identne ISO/FDIS 16484-5:2012
ja identne
FprEN ISO 16484-5:2012
Tähtaeg 30.06.2012
Building automation and control systems - Part 5: Data communication protocol (ISO/FDIS 16484-5:2012)
This part of ISO 16484 defines data communication services and protocols for computer equipment used for monitoring and control of heating, ventilation, air-conditioning and refrigeration (HVAC&R) and other building systems. It defines, in addition, an abstract, object-oriented representation of information communicated between such equipment, thereby facilitating the application and use of digital control technology in buildings. The scope and field of application are furthermore detailed in Clause 2 of the enclosed ANSI/ASHRAE publication.
Keel: Inglise
prEN ISO 16283-1
Identne ISO/DIS 16283-1:2012
ja identne
prEN ISO 16283-1 rev:2012
Tähtaeg 30.06.2012
Acoustics - Field measurement of sound insulation in buildings and of building elements - Part 1: Airborne sound insulation (ISO/DIS 16283-1:2012)
This part of ISO 16283 specifies procedures to determine the airborne sound insulation between two rooms in a building using sound pressure measurements. It is intended for room volumes in the range from 10 to 250 m3 in the frequency range from 50 to 5 000 Hz. The test results can be used to quantify, assess and compare the airborne sound insulation in unfurnished or furnished rooms where the sound field may, or may not approximate to a diffuse field. The measured airborne sound insulation is frequency-dependent and can be converted into a single number to characterise the acoustic performance using the rating procedures in ISO 717-1.
Keel: Inglise