Back

Sorry - this product is no longer available

EVS-EN 62196-1:2012

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements

General information
Withdrawn from 12.01.2015
Base Documents
IEC 62196-1:2011; EN 62196-1:2012
Directives or regulations
2014/35/EU Low voltage (LVD)

Although the standard’s status is withdrawn, it still has the presumption of conformity in the meaning of regulation 2014/35/EU and conformance with the regulation ’s requirements can be guaranteed by using the withdrawn version of the standard. The presumption of conformity is valid until a corresponding amendment is published in the Official Journal of the European Union.
 
To view the latest lists of harmonised standards published in the Official Journal of the European Union, visit: 
http://ec.europa.eu/growth/single-market/european-standards/harmonised-standards/

Standard history

Status
Date
Type
Name
12.01.2015
Main
03.09.2014
Amendment
EVS-EN 62196-1:2012/A12:2014
06.05.2013
Amendment
EVS-EN 62196-1:2012/A11:2013
05.06.2012
Main
EVS-EN 62196-1:2012
Main
EVS-EN 62196-1:2004
This part of IEC 62196 is applicable to plugs, socket-outlets, connectors, inlets and cable assemblies for electric vehicles (EV), herein referred to as “accessories”, intended for use in conductive charging systems which incorporate control means, with a rated operating voltage not exceeding - 690 V a.c. 50 Hz – 60 Hz, at a rated current not exceeding 250 A, - 1 500 V d.c. at a rated current not exceeding 400 A. These accessories and cable assemblies are intended to be used for circuits specified in IEC 61851-1:2010 which operate at different voltages and frequencies and which may include ELV and communication signals. The accessories covered by this standard are intended only to be used with vehicles that comply with the requirements of 7.2.3.1 of IEC 61851-1:2010. These accessories and cable assemblies are to be used in an ambient temperature of between -30 °C and +50 °C. NOTE In some countries, other requirements may apply. These accessories are intended to be connected only to cables with copper or copper-alloy conductors. The accessories covered by this standard are for use in certain modes of charging EVs. These modes are defined in IEC 61851-1:2010. These definitions and a description of the types of connection (cases A, B and C), also described in IEC 61851-1:2010, are reproduced herein as Annex A. NOTE In the following country, Mode 1 will not be allowed: UK. This standard does not apply to those standardised accessories used in charging systems where the use of such accessories constructed to the requirements of other standards is permitted (e.g. in mode 1 and mode 2). Such standardized accessories may be used for those situations (mode and case) identified in IEC 61851-1:2010. This standard can be used as a guide for accessories with a lesser number of contacts and lower ratings for use with light duty vehicles.
*
*
*
PDF
28.06 € incl tax
Paper
28.06 € incl tax
Browse standard from 2.44 € incl tax
Standard monitoring

Customers who bought this item also bought

Main

EVS-EN 61851-1:2011

Electric vehicle conductive charging system Part 1: General requirements
Withdrawn from 16.07.2019
Main

EVS-EN 62196-2:2012

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories
Newest version Withdrawn from 16.05.2017
Main

EVS-EN 61851-21:2002

Electric vehicle conductive charging system - Part 21: Electric vehicle requirements for conductive connection to an a.c/d.c. supply
Withdrawn from 17.05.2021
Main

EVS-EN 61851-22:2002

Electric vehicle conductive charging system - Part 22: AC electric vehicle charging station
Newest version Withdrawn from 15.10.2020