Tagasi

EVS-EN 1329-1:2014+A1:2018

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the systems

Üldinfo
Kehtetu alates 15.12.2020
Alusdokumendid
EN 1329-1:2014+A1:2018
Direktiivid või määrused
puuduvad

Standardi ajalugu

Staatus
Kuupäev
Tüüp
Nimetus
15.12.2020
Põhitekst
16.04.2018
Põhitekst + muudatus
04.03.2014
Põhitekst
EVS-EN 1329-1:2014
This part of EN 1329 specifies the requirements for solid wall unplasticised poly(vinyl chloride) (PVC-U) pipes, fittings and the system intended for:
-  soil and waste discharge applications (low and high temperature) inside buildings (application area code "B");
-  soil and waste discharge applications (low and high temperature) for both inside buildings and buried in ground within the building structure (application area code "BD").
NOTE 1  The intended use is reflected in the marking of products by "B" or "BD".
NOTE 2  For use buried in ground within the building structure are intended only those components (marked with "BD") with nominal outside diameters equal to or greater than 75 mm.
This part of EN 1329 is also applicable to PVC-U pipes, fittings and the system intended for the following purposes:
-  ventilating part of the pipework in association with discharge applications;
-  rainwater pipework within the building structure.
It also specifies the test parameters for the test method referred to in this standard.
This standard covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours.
NOTE 3  It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
For external above ground application additional requirements depending on the climate should be agreed between the manufacturer and the user.
NOTE 4  Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 15.
NOTE 5  Joints and adhesives are considered to be part of the system as covered in the scope.
*
*
*
PDF
28,06 € koos KM-ga
Paber
28,06 € koos KM-ga
Sirvi standardit alates 2,44 € koos KM-ga
Standardi monitooring

Teised on ostnud veel

Põhitekst

EVS-EN ISO 377:2017

Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:2017)
Uusim versioon Kehtiv alates 02.08.2017
Põhitekst

CEN/TS 1329-2:2018

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity
Kehtetu alates 01.02.2021
Põhitekst

EVS-EN 10080:2006

Betooni sarrusteras. Keevitatav sarrusteras. Üldsätted
Uusim versioon Kehtiv alates 08.12.2006
Põhitekst

EVS-EN ISO 15630-1:2010

Betooni sarrustamiseks ja pingestamiseks kasutatav teras. Katsemeetodid. Osa 1: Armatuurraud, armatuurvõrk ja armatuurtraat
Kehtetu alates 15.03.2019