Tagasi

Vabandust – see toode pole enam saadaval

EVS-EN 62196-1:2012/A11:2013

Pistikud, pistikupesad, sõiduki-pistikühendused ja sõidukisisendid. Elektrisõidukite juhtivuslik laadimine. Osa 1: Üldnõuded

Üldinfo
Kehtetu alates 12.01.2015
Alusdokumendid
EN 62196-1:2012/A11:2013
Direktiivid või määrused
2014/35/EU Madalpinge

Olgugi et standard on tühistatud, on sellel Euroopa Liidu õigusakti 2014/35/EU mõistes siiski vastavuse eeldus ning vastavust  õigusakti nõuetega saab tagada, kui kasutada standardi tühistatud versiooni. Vastavuse eeldus kehtib, kuni vastav muudatus avaldatakse Euroopa Liidu Teatajas.
 
Uusimat Euroopa Liidu Teatajas avaldatud kooskõlastatud standardite nimekirja saad vaadata siit: 
http://ec.europa.eu/growth/single-market/european-standards/harmonised-standards/

Standardi ajalugu

Staatus
Kuupäev
Tüüp
Nimetus
12.01.2015
Põhitekst
06.05.2013
Muudatus
EVS-EN 62196-1:2012/A11:2013
05.06.2012
Põhitekst
EVS-EN 62196-1:2012
This part of IEC 62196 is applicable to plugs, socket-outlets, connectors, inlets and cable assemblies for electric vehicles (EV), herein referred to as “accessories”, intended for use in conductive charging systems which incorporate control means, with a rated operating voltage not exceeding - 690 V a.c. 50 Hz – 60 Hz, at a rated current not exceeding 250 A, - 1 500 V d.c. at a rated current not exceeding 400 A. These accessories and cable assemblies are intended to be used for circuits specified in IEC 61851-1:2010 which operate at different voltages and frequencies and which may include ELV and communication signals. The accessories covered by this standard are intended only to be used with vehicles that comply with the requirements of 7.2.3.1 of IEC 61851-1:2010. These accessories and cable assemblies are to be used in an ambient temperature of between -30 °C and +50 °C. NOTE In some countries, other requirements may apply. These accessories are intended to be connected only to cables with copper or copper-alloy conductors. The accessories covered by this standard are for use in certain modes of charging EVs. These modes are defined in IEC 61851-1:2010. These definitions and a description of the types of connection (cases A, B and C), also described in IEC 61851-1:2010, are reproduced herein as Annex A. This standard does not apply to those standardised accessories used in charging systems where the use of such accessories constructed to the requirements of other standards is permitted (e.g. in mode 1 and mode 2). Such standardized accessories may be used for those situations (mode and case) identified in IEC 61851-1:2010. This standard can be used as a guide for accessories with a lesser number of contacts and lower ratings for use with light duty vehicles.
*
*
*
PDF
7,32 € koos KM-ga
Paber
7,32 € koos KM-ga
Sirvi standardit alates 2,44 € koos KM-ga
Standardi monitooring

Teised on ostnud veel

Põhitekst

EVS-EN 61851-1:2011

Elektrisõidukite juhtivuslik laadimissüsteem. Osa 1: Üldnõuded
Kehtetu alates 16.07.2019
Muudatus

EVS-EN 62196-2:2012/A11:2013

Pistikud, pistikupesad, sõiduki-pistikühendused ja sõidukisisendid. Elektrisõidukite juhtivuslik laadimine. Osa 2: Kontaktsõrmedel ja -pesadel põhinevate vahelduvvooluseadiste mõõtmelise ühilduvuse ja vahetatavuse nõuded
Uusim versioon Kehtetu alates 16.05.2017