Tagasi

prEN 302 326-3 V2.1.0

Fixed Radio Systems; Multipoint Equipment and Antennas; Part 3: Multipoint Antennas

Üldinfo
Kavand
Alusdokumendid
Draft ETSI EN 302 326-3 V2.1.0
Tegevusala (ICS grupid)
33 SIDETEHNIKA
Direktiivid või määrused
puuduvad
ETSI standardeid meie e-poest osta ei saa. Neid on võimalik tasuta alla laadida siit.
Standardi ajalugu
Staatus
Kuupäev
Tüüp
Nimetus
1.1 General The present document is applicable to antennas (were it stand-alone, dedicated or integral antennas according the definitions in clause 3.1) used in Multipoint (MP) Digital Fixed Radio Systems (DFRS) (see note 1) intended for use in the frequency bands identified in ETSI EN 302 326-2. NOTE 1: Applications intended for offering in the bands 3,4 GHz to 3,8 GHz the option of Nomadic Wireless Access (NWA), according to the NWA definition in Recommendation ITU-R F.1399 [i.3], are also considered in the scope of the present document. For Multipoint Fixed Radio Systems, antenna characteristics are not considered relevant to essential requirements under article 3.2 of Directive 2014/53/EU (see note 2). Antenna characteristics in the present document are considered applicable whenever they are considered appropriate for the associated multipoint radio system. NOTE 2: Rationale can be found in ETSI TR 101 506. 1.2 Antenna types and operating frequency The present document is applicable to multipoint radio system antennas of both linear (single or dual) polarization and circular (single or dual) polarization. Linear polarization antennas may support either or both of two mutually perpendicular planes of polarization. These planes are frequently, though not always, horizontal and vertical. Circular polarization antennas may support either right hand or left hand polarization or, for dual polarization, both. The RPE directional characteristics and polarization characteristics (co-polar and cross-polar and for either linear or circular polarized antennas) impact on the interference to be considered in network planning. A number of antenna options are defined in the present document. Table 1 outlines the multipoint antenna types and their operating frequencies described in the present document. NOTE: Antenna characteristics are not standardized at frequencies below 1 GHz. Table 1: Antenna Types Frequency Range (see note); Types; Polarization; Notes; 1 GHz to 3 GHz; Directional/Sectored single beam/ Omnidirectional; Linear; The sectored and omnidirectional antennas may have a symmetric or asymmetric radiation pattern in the elevation plane. 3 GHz to 5,9 GHz, 5,9 GHz to 8,5 GHz and 8,5 GHz to 11 GHz; Directional/Sectored single beam/Sectored multi-beam (up to 5,9 GHz only)/Omnidirectional; Linear; The sectored single and omnidirectional antennas may have a symmetric or asymmetric radiation pattern in the elevation plane. The sectored multibeam antennas have a symmetric radiation pattern only. 1 GHz to 11 GHz; Directional/Sectored single beam/Omnidirectional; Circular; The sectored and omnidirectional antennas may have a symmetric or asymmetric radiation pattern in the elevation plane. 24,25 GHz to 30 GHz; Directional/Sectored single beam; Linear; 30 GHz to 40,5 GHz and 40,5 GHZ to 43,5 GHz; Directional/Sectored single beam/Omnidirectional; Linear; The omnidirectional antennas may have a symmetric or asymmetric radiation pattern in the elevation plane. NOTE: Attention is drawn to the fact that the specific operating bands are subject of CEPT or national licensing rules. Currently applicable Fixed Service bands and channel plans are described in ETSI EN 302 326-2, although the applicability of these Fixed Service bands is at the discretion of the national administrations. Therefore, the present document applies only to those bands which are allocated to the Fixed Service and/or assigned by national regulations to MP applications on the date on which the EN was published. 1.3 Profiles The present document and associated ETSI EN 302 326-2 for equipment and systems allows many distinct types of equipment, several different antenna types and several ways in which they might be interconnected to form a network. However, the applicability is limited to certain combinations of attributes and these combinations of attributes are called "profiles": • Equipment profiles. • Antenna profiles. • System profiles. Annex A discusses Equipment, Antennas and Sytem Profiles for multipoint systems in the scope of this multi-part deliverable.
*
*
*
Standardi monitooring