Tagasi

EVS-EN ISO 5163:2014

Petroleum products - Determination of knock characteristics of motor and aviation fuels - Motor method (ISO 5163:2014)

Üldinfo
Kehtiv alates 01.07.2014
Alusdokumendid
ISO 5163:2014; EN ISO 5163:2014
Tegevusala (ICS grupid)
75.160.20 Vedelkütused
Direktiivid või määrused
puuduvad

Standardi ajalugu

Staatus
Kuupäev
Tüüp
Nimetus
01.07.2014
Põhitekst
07.05.2009
Parandus
04.01.2006
Põhitekst
This International Standard establishes the rating of liquid spark-ignition engine fuel in terms of an arbitrary scale of octane numbers using a standard single-cylinder, four-stroke cycle, variable-compression ratio, carburetted, CFR engine operated at constant speed. Motor octane number (MON) provides a measure of the knock characteristics of motor fuels in automotive engines under severe conditions of operation. The motor octane number provides a measure of the knock characteristics of aviation fuels in aviation piston engines, by using an equation to correlate to aviation-method octane number or performance number (lean-mixture aviation rating). This International Standard is applicable for the entire scale range from 0 MON to 120 MON, but the working range is 40 MON to 120 MON. Typical motor fuel testing is in the range of 80 MON to 90 MON. Typical aviation fuel testing is in the range of 98 MON to 102 MON. This International Standard is applicable for oxygenate-containing fuels containing up to 4,0 % (m/m) oxygen. NOTE 1 Work is under way to check the possibility to use the method for gasoline containing up to 25 %(V/V) and up to 85 %(V/V) ethanol. Certain gases and fumes, such as halogenated refrigerants used in air-conditioning equipment that can be present in the area where the CFR engine is located, may have a measurable effect on the MON rating. Electrical power transient voltage or frequency surges or distortion can affect MON ratings. NOTE 2 This International Standard specifies operating conditions in SI units but engine measurements may be specified in inch-pound units because these were the units used in the manufacture of the equipment, and thus some references in this International Standard include these units in parenthesis. NOTE 3 For the purposes of this standard, the terms “% (m/m)” and “% (V/V)” are used to represent the mass fraction (μ) and the volume fraction (φ) of a material respectively.
*
*
*
PDF
20,74 € koos KM-ga
Paber
20,74 € koos KM-ga
Sirvi standardit alates 2,44 € koos KM-ga
Standardi monitooring

Teised on ostnud veel

Põhitekst

EVS-EN ISO 5164:2014

Naftatooted. Mootorikütuste detonatsioonikarakteristikute määramine. Uurimismeetod
Uusim versioon Kehtiv alates 01.07.2014
Põhitekst

EVS-EN 238:2000

Vedelad naftasaadused. Bensiin. Benseenisisalduse määramine infrapuna-spektromeetria abil
Uusim versioon Kehtiv alates 01.01.2000
Muudatus

EVS-EN 238:2000/A1:2004

Vedelad naftasaadused. Bensiin. Benseenisisalduse määramine infrapuna-spektromeetria abil
Uusim versioon Kehtiv alates 10.03.2004
Põhitekst

EVS-EN 12662:2014

Liquid petroleum products - Determination of total contamination in middle distillates, diesel fuels and fatty acid methyl esters
Uusim versioon Kehtiv alates 01.04.2014