Tagasi

EVS-EN IEC 60512-23-3:2019

Connectors for electrical and electronic equipment - Tests and measurements - Part 23-3: Screening and filtering tests - Test 23c: Shielding effectiveness of connectors and accessories - Line injection method

Üldinfo
Kehtiv alates 15.03.2019
Alusdokumendid
IEC 60512-23-3:2018; EN IEC 60512-23-3:2019
Direktiivid või määrused
puuduvad

Standardi ajalugu

Staatus
Kuupäev
Tüüp
Nimetus
15.03.2019
Põhitekst
01.01.2003
Põhitekst
This part of IEC 60512 defines a standard test method for measuring the shielding
effectiveness SE of a shielded connector, or of a connector not provided with integral shield
once fitted with a shielding accessory and terminated with a screened cable.
The complete assembly has a continuous 360° shielding capability throughout its length.
NOTE 1 Practically, continuous 360° shielding is not always achievable based on the geometry of the connector.
NOTE 2 Shielding" is used in this document with the same meaning as "screening".
This test method can be applied to shielded connectors and to connector accessories with shielding capability. The following different connector designs can be tested:
- circular connectors;
- rectangular connectors;
- connectors for printed boards;
- connector shielding accessories.
NOTE 3 For the definition of "accessory" see IEV 581-24-10. A shielding accessory i.e. an accessory that confers shielding to a non-inherently shielded connector, may be a suitable set of shielded housings providing electrical continuity, along the mated connector set, between the screen of the (screened) cable at the cable outlet of the free cable connector housing and the metallic mounting surface for the fixed connector housing. The free connector housing is provided with a cable screen clamp.
This test method utilizes the principle that the intrinsic shielding property of the connector/accessory/cable assembly is its surface transfer impedance ZT which can be expressed as the longitudinal voltage inside the shield, relative to the current flow on the outside shell.
This test method is based on two impedance-matched circuits. See Figure 1 for the measurement principle. The connector specimen under test is integrated into the secondary circuit 02. The impedance-matched injection line of the primary circuit 01, which activates the electromagnetic field, runs parallel to the surface of the specimen under test.
This test is also suitable for measuring the shielding effectiveness of a connector fitted with triaxial contacts terminated with shielded, twisted pair cables, as used in data bus systems.
NOTE 4 This standard has been adopted by ASD-STAN (formerly known as AECMA) as EN 2591-212.
*
*
*
PDF
13,42 € koos KM-ga
Paber
13,42 € koos KM-ga
Sirvi standardit alates 2,44 € koos KM-ga
Standardi monitooring

Teised on ostnud veel

Põhitekst

EVS-EN 60512-15-8:2006

Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 15: Mechanical tests on contacts and terminations - Section 8: Test 15h - Contact retention system resistance to tool application
Uusim versioon Kehtiv alates 01.02.2006
Põhitekst

EVS-EN 60512-19-3:2002

Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 19: Chemical resistance tests - Section 3: Test 19c - Fluid resistance
Uusim versioon Kehtiv alates 01.01.2003
Põhitekst

EVS-EN 60512-25-1:2003

Connectors for electronic equipment -Tests and measurements - Part 25-1: Test 25a - Crosstalk ratio
Uusim versioon Kehtiv alates 01.02.2003
Põhitekst

EVS-EN 60512-25-2:2003

Connectors for electronic equipment -Tests and measurements - Part 25-2: Test 25b: Attenuation (insertion loss)
Uusim versioon Kehtiv alates 01.02.2003