Skip to main content
Tagasi

EVS-EN ISO 898-5:2012

Mechanical properties of fasteners made of carbon steel and alloy steel - Part 5: Set screws and similar threaded fasteners with specified hardness classes - Coarse thread and fine pitch thread (ISO 898-5:2012)

Üldinfo

Kehtiv alates 03.07.2012
Alusdokumendid
ISO 898-5:2012; EN ISO 898-5:2012
Direktiivid või määrused
puuduvad

Standardi ajalugu

Staatus
Kuupäev
Tüüp
Nimetus
03.07.2012
Põhitekst
This part of ISO 898 specifies mechanical and physical properties of set screws and similar threaded fasteners made of carbon steel or alloy steel when tested at an ambient temperature range of 10 °C to 35 °C. Fasteners (the term used when set screws and similar threaded fasteners are considered all together) which conform to the requirements of this part of ISO 898 are evaluated at that ambient temperature range. Fasteners in conformance with this part of ISO 898 are classified to specified hardness classes and are intended for use under compressive stress only. NOTE Fasteners conforming to the requirements of this part of ISO 898 are used in applications ranging from -50 °C to +150 °C. It is the responsibility of users to consult an experienced fastener metallurgist for temperatures outside the range of -50 °C to +150 °C and up to a maximum temperature of +300 °C when determining appropriate choices for a given application. This part of ISO 898 is applicable to set screws and similar threaded fasteners: - made of carbon steel or alloy steel, - having a triangular ISO metric screw thread in conformance with ISO 68-1, - with a coarse pitch thread of M1,6 to M30, and a fine pitch thread of M8×1 to M30×2, - with diameter/pitch combinations in conformance with ISO 261 and ISO 262, and - having thread tolerances in conformance with ISO 965-1 and ISO 965-2. It does not specify requirements for such properties as - tensile strength, - shear strength, - weldability, - corrosion resistance, or - the ability to withstand temperatures above +150 °C or below −50 °C.

Nõutud väljad on tähistatud *

*
*
*
PDF
15,86 € koos KM-ga
Paber
15,86 € koos KM-ga
Sirvi standardit alates 2,44 € koos KM-ga
Standardi monitooring

Teised on ostnud veel

Põhitekst

EVS-EN ISO 898-1:2013

Süsinikterasest ja legeeritud terasest kinnitite mehaanilised omadused. Osa 1: Spetsifitseeritud omadusklassidega poldid, kruvid ja tikkpoldid. Jämekeere ja peenkeere
Uusim versioon Kehtiv alates 05.02.2013
Põhitekst

EVS-EN ISO 10684:2004

Fasteners - Hot dip galvanized coatings
Uusim versioon Kehtiv alates 08.11.2004
Põhitekst

EVS-EN ISO 898-2:2012

Mechanical properties of fasteners made of carbon steel and alloy steel - Part 2: Nuts with specified property classes - Coarse thread and fine pitch thread (ISO 898-2:2012)
Kehtetu alates 15.02.2023
Põhitekst

EVS-EN 20898-7:1999

Kinnitusdetailide mehaanilised omadused. Osa 7: 1 - 10 mm nimiläbimõõduga poltide ja kruvide väändekatse ning minimaalsed väändemomendid
Uusim versioon Kehtiv alates 01.01.2000