Infoteenus
53 TÕSTE- JA TEISALDUS-SEADMED
Uued standardid
EVS-EN 16842-11:2026
Powered industrial trucks - Visibility - Test methods and verification - Part 11: Pallet-stacking trucks (rider controlled)
Käsitlusala: This document specifies the requirements and test procedures for 360° visibility of self-propelled industrial rider-controlled pallet-stacking trucks in accordance with ISO 5053 1 (herein after referred to as trucks), without a load and it is intended to be used in conjunction with EN 16842 1.
This document also applies to pedestrian controlled trucks with foldable platform when used in ride-on mode.
Pedestrian-controlled trucks without an operator on the platform and pedestrian-propelled trucks are not covered by this document.
Where specific requirements in this part are modified from the general requirements in EN 16842 1, the requirements of this part are truck specific and intended to be used for self-propelled industrial stand-on pallet-stacking trucks.
This part of EN 16842 deals with all significant hazards, hazardous situations or hazardous events relevant to the visibility of the operator for applicable machines when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
This document also applies to pedestrian controlled trucks with foldable platform when used in ride-on mode.
Pedestrian-controlled trucks without an operator on the platform and pedestrian-propelled trucks are not covered by this document.
Where specific requirements in this part are modified from the general requirements in EN 16842 1, the requirements of this part are truck specific and intended to be used for self-propelled industrial stand-on pallet-stacking trucks.
This part of EN 16842 deals with all significant hazards, hazardous situations or hazardous events relevant to the visibility of the operator for applicable machines when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
Alusdokumendid: EN 16842-11:2026
ISO 4195:2026
Conveyor belts with heat-resistant rubber covers — Heat resistance of covers — Requirements and test methods
Käsitlusala: This document specifies requirements and test methods for the relative level of heat resistance of conveyor belt covers made of rubber. It specifies the permissible variations of hardness, elongation at break and tensile strength after exposure to heat.
It is applicable only to those conveyor belts having a carryside (top) cover thickness greater than or equal to 4 mm. It is not suitable or valid for light conveyor belts as described in ISO 21183-1.
It is applicable only to those conveyor belts having a carryside (top) cover thickness greater than or equal to 4 mm. It is not suitable or valid for light conveyor belts as described in ISO 21183-1.
Alusdokumendid:
Asendab: ISO 4195:2012
ISO 10245-5:2026
Cranes — Limiting and indicating devices — Part 5: Bridge and gantry cranes
Käsitlusala: This document specifies the requirements for devices that either limit or indicate the loads, motions, performance and environment of bridge and gantry cranes.
The general requirements for limiting and indicating devices for cranes are given in ISO 10245-1.
The general requirements for limiting and indicating devices for cranes are given in ISO 10245-1.
Alusdokumendid:
Asendab: ISO 10245-5:1995
Asendatud standardid
ISO 4195:2012
Conveyor belts with heat-resistant rubber covers -- Heat resistance of covers -- Requirements and test methods
Käsitlusala: ISO 4195:2012 specifies requirements and test methods for the relative level of heat resistance of conveyor belt covers made of rubber. It gives the permissible variations of hardness, elongation at break and tensile strength after exposure to heat. It is applicable only to those conveyor belts having a cover thickness greater than or equal to 4 mm. It is not suitable or valid for light conveyor belts as described in ISO 21183-1.
Alusdokumendid:
Asendatud: ISO 4195:2026
ISO 10245-5:1995
Cranes -- Limiting and indicating devices -- Part 5: Overhead travelling and portal bridge cranes
Käsitlusala: Specifies the requirements for limiting and indicating devices of bridges and gantry cranes for loads, motions, performance and environment. General requirements for limiting and indicating devices for cranes are given in ISO 10245-1.
Alusdokumendid:
Asendatud: ISO 10245-5:2026
Kavandid
prEN 1570-1
Safety requirements for lifting tables - Part 1: Lifting tables serving up to two fixed landing
Käsitlusala: 1.1 This document specifies the safety requirements for lifting tables which fulfil the following characteristics:
— serving no more than 2 fixed landings but able to pass a fixed landing and,
— having a vertical travel speed of no more than 0,15 m/s, unless the lifting table is safe by position and,
— raising or lowering goods (with or without operator(s) and/or authorized person(s)) with a fixed, movable or mobile lifting table or,
— raising or lowering operator(s) and/or authorized person(s) with or without goods, to positions where they can carry out work from a fixed lifting table that is guided throughout its vertical travel only.
1.2 This document specifies the appropriate technical measures for eliminating and reducing the risks arising from the significant hazards listed in Annex B.
1.3 This document does not apply to the following equipment:
— lifting tables with a vertical travel speed exceeding 0,15 m/s, unless the lifting table is safe by position;
— lifting tables, serving more than 2 fixed landings of a construction, for lifting goods, with a vertical travel speed not exceeding 0,15 m/s (EN 1570 2:2016);
— lifting tables, serving more than 2 fixed landings of a construction, for lifting operators, with a vertical travel speed not exceeding 0,15 m/s;
— lifting tables carrying operators and installed in full enclosures with a vertical travel speed not exceeding 0,15 m/s;
— lifting tables used on ships;
— lifting tables designed for artists and stage set features during artistic performances (EN 17206:2020);
— power operated lifting platforms for persons with impaired mobility (EN 81 41:2010);
— mobile lifting tables for airport ground support equipment (EN 1915 2:2001+A1:2009 and EN 12312 1:2013);
— mobile elevating work platforms (EN 280 1:2022);
— vehicle servicing lifts (EN 1493:2022);
— mobile lifting tables used for firefighting (EN 1777:2010);
— mobile lifting tables with a horizontal travelling speed of more than 1,6 m/s;
— rail dependent storage and retrieval equipment (EN 528:2021);
— scissor lift pallet trucks (EN ISO 3691 5:2015);
— lifting tables suspended from a ceiling.
1.4 This document does not consider the requirements for:
— operation in severe conditions (e.g. extreme climates, freezer applications, strong magnetic fields);
— operation subject to special rules (e.g. potentially explosive atmospheres, mines);
— handling of loads, the nature of which could lead to dangerous situations (e.g. molten metal, acids, radiating materials, particularly brittle loads, loose loads (gravel, tubes));
— hazards occurring during construction, transportation, and disposal;
— equipment installed on the load platform or the replacing or maintaining of it;
— integration into broader systems or other machines, etc.;
— cable-less controls, i.e. wireless;
— lifting tables where the hydraulic pressure is derived directly from gas pressure;
— lifting tables powered by internal combustion engines.
This document is not applicable to lifting tables manufactured before the date of its publication.
— serving no more than 2 fixed landings but able to pass a fixed landing and,
— having a vertical travel speed of no more than 0,15 m/s, unless the lifting table is safe by position and,
— raising or lowering goods (with or without operator(s) and/or authorized person(s)) with a fixed, movable or mobile lifting table or,
— raising or lowering operator(s) and/or authorized person(s) with or without goods, to positions where they can carry out work from a fixed lifting table that is guided throughout its vertical travel only.
1.2 This document specifies the appropriate technical measures for eliminating and reducing the risks arising from the significant hazards listed in Annex B.
1.3 This document does not apply to the following equipment:
— lifting tables with a vertical travel speed exceeding 0,15 m/s, unless the lifting table is safe by position;
— lifting tables, serving more than 2 fixed landings of a construction, for lifting goods, with a vertical travel speed not exceeding 0,15 m/s (EN 1570 2:2016);
— lifting tables, serving more than 2 fixed landings of a construction, for lifting operators, with a vertical travel speed not exceeding 0,15 m/s;
— lifting tables carrying operators and installed in full enclosures with a vertical travel speed not exceeding 0,15 m/s;
— lifting tables used on ships;
— lifting tables designed for artists and stage set features during artistic performances (EN 17206:2020);
— power operated lifting platforms for persons with impaired mobility (EN 81 41:2010);
— mobile lifting tables for airport ground support equipment (EN 1915 2:2001+A1:2009 and EN 12312 1:2013);
— mobile elevating work platforms (EN 280 1:2022);
— vehicle servicing lifts (EN 1493:2022);
— mobile lifting tables used for firefighting (EN 1777:2010);
— mobile lifting tables with a horizontal travelling speed of more than 1,6 m/s;
— rail dependent storage and retrieval equipment (EN 528:2021);
— scissor lift pallet trucks (EN ISO 3691 5:2015);
— lifting tables suspended from a ceiling.
1.4 This document does not consider the requirements for:
— operation in severe conditions (e.g. extreme climates, freezer applications, strong magnetic fields);
— operation subject to special rules (e.g. potentially explosive atmospheres, mines);
— handling of loads, the nature of which could lead to dangerous situations (e.g. molten metal, acids, radiating materials, particularly brittle loads, loose loads (gravel, tubes));
— hazards occurring during construction, transportation, and disposal;
— equipment installed on the load platform or the replacing or maintaining of it;
— integration into broader systems or other machines, etc.;
— cable-less controls, i.e. wireless;
— lifting tables where the hydraulic pressure is derived directly from gas pressure;
— lifting tables powered by internal combustion engines.
This document is not applicable to lifting tables manufactured before the date of its publication.
Alusdokumendid: prEN 1570-1