Skip to main content
Tagasi

Vabandust – see toode pole enam saadaval

EVS-EN 848-1:2007+A2:2012

Safety of woodworking machines - One side moulding machines with rotating tool - Part 1: Single spindle vertical moulding machines CONSOLIDATED TEXT

Üldinfo

Kehtetu alates 02.01.2018
Alusdokumendid
EN 848-1:2007+A2:2012
Tegevusala (ICS grupid)
79.120.10 Puidutöötluspingid
Direktiivid või määrused
puuduvad

Standardi ajalugu

Staatus
Kuupäev
Tüüp
Nimetus
02.01.2018
Põhitekst
06.11.2012
Põhitekst + muudatus
EVS-EN 848-1:2007+A2:2012
Põhitekst + muudatus
EVS-EN 848-1:2007+A1:2010
This document specifies all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to stationary and displaceable hand fed single spindle vertical moulding machines (with or without demountable power feed unit), herein after referred to as "machines", designed to cut solid wood, chip board, fibreboard, plywood and also these materials if they are covered with plastic laminate or edgings when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Machines which are designed to work wood based materials may also be used for working hardened plastic materials with similar physical characteristics as wood. NOTE 1 For the definition of stationary and displaceable machine see 3.2.17 and 3.2.18. This document does not apply to: a) machines equipped with outboard bearings; b) machines equipped with powered movements of front extension table and/or tenoning sliding table; c) hand held woodworking machines or any adaptation permitting their use in a different mode, i.e. bench mounting; NOTE 2 Hand-held motor-operated electric tools are dealt with in EN 60745-1:2009 together with EN 60745-2-17:2010$. d) machines set up on a bench or a table similar to a bench, which are intended to carry out work in a stationary position, capable of being lifted by one person by hand. The bench can also be an integrated part of the machine if it consists of hinged legs which can be extended down; NOTE 3 Transportable motor-operated electric tools are dealt with in EN 61029-1:2009 together with EN 61029-2-8:2010$. This document is not applicable to hand fed single spindle vertical moulding machines which are manufactured before the date of its publication as EN. NOTE 4 Machines covered by this document are listed under 7 of Annex IV of the Machinery Directive.

Nõutud väljad on tähistatud *

*
*
*
PDF
39,04 € koos KM-ga
Paber
39,04 € koos KM-ga
Sirvi standardit alates 2,44 € koos KM-ga
Standardi monitooring

Teised on ostnud veel

Põhitekst + muudatus

EVS-EN 860:2007+A2:2012

Puidutöötlemismasinate ohutus. Ühepoolsed paksushöövelpingid KONSOLIDEERITUD TEKST
Kehtetu alates 16.07.2019
Põhitekst

EVS-EN ISO 11681-1:2011

Metsatöömasinad. Kaasaskantavate kettsaagide ohutusnõuded ja katsetamine. Osa 1: Hooldusraiel kasutatavad kettsaed (ISO 11681-1:2011)
Kehtetu alates 01.06.2022
Põhitekst

EVS-EN ISO 13856-1:2013

Masinate ohutus. Survetundlikud kaitseseadmed. Osa 1: Survetundlike mattide ja survetundlike põrandate konstrueerimise ja katsetamise põhialused
Uusim versioon Kehtiv alates 04.06.2013
Põhitekst + muudatus

EVS-EN 12622:2010+A1:2013

Tööpinkide ohutus. Hüdraulilised painutuspressid
Uusim versioon Kehtiv alates 14.11.2013