Skip to main content
Back

EVS-EN 62196-2:2012

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories

General information

Withdrawn from 16.05.2017
Base Documents
IEC 62196-2:2011; EN 62196-2:2012
Directives or regulations
2014/35/EU Low voltage (LVD)

Although the standard’s status is withdrawn, it still has the presumption of conformity in the meaning of regulation 2014/35/EU and conformance with the regulation ’s requirements can be guaranteed by using the withdrawn version of the standard. The presumption of conformity is valid until a corresponding amendment is published in the Official Journal of the European Union.
 
To view the latest lists of harmonised standards published in the Official Journal of the European Union, visit: 
http://ec.europa.eu/growth/single-market/european-standards/harmonised-standards/

Standard history

Status
Date
Type
Name
16.05.2017
Main
03.09.2014
Amendment
06.05.2013
Amendment
05.06.2012
Main
This standard applies to plugs, socket-outlets, vehicle connectors and vehicle inlets with pins and contact-tubes of standardized configurations, herein referred to as accessories. They have a nominal rated operating voltage not exceeding 500 V a.c., 50 to 60 Hz, and a rated current not exceeding 63 A three-phase or 70 A single phase, for use in conductive charging of electric vehicles. This standard covers the basic interface accessories for vehicle supply as specified in IEC 62196-1, and intended for use in conductive charging systems for circuits specified in IEC 61851-1:2010. Electric vehicles covers all road vehicles, including plug-in hybrid road vehicles (PHEV), that derive all or part of their energy from on-board batteries. NOTE 1 These accessories may provide a contact that can be used for the proximity contact function. These accessories are intended to be used for circuits specified in IEC 61851-1:2010 which operate at different voltages and frequencies and which may include ELV and communication signals. These accessories may be used for bidirectional energy transmission (under consideration). This standard applies to the accessories to be used in an ambient temperature of between - 30 °C and + 50 °C. NOTE 2 In the following country, other requirements may apply: FI. These accessories are intended to be connected only to cables with copper or copper-alloy conductors. Vehicle inlet and vehicle connector to this standard are intended to be used for charging in modes 1, 2 and 3, cases B and C. The socket-outlets and plugs covered by this standard are intended to be used for charging mode 3 only, case A and B. The modes and permissible connections are specified in Part 1.

Required fields are indicated with *

*
*
*
PDF
31.72 € incl tax
Paper
31.72 € incl tax
Browse standard from 2.44 € incl tax
Standard monitoring

Customers who bought this item also bought

Amendment

EVS-EN 62196-2:2012/A11:2013

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories
Newest version Withdrawn from 16.05.2017
Amendment

EVS-EN 62196-2:2012/A12:2014

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories
Newest version Withdrawn from 16.05.2017
Main

EVS-EN 61851-21:2002

Electric vehicle conductive charging system - Part 21: Electric vehicle requirements for conductive connection to an a.c/d.c. supply
Withdrawn from 17.05.2021
Main

EVS-EN 61851-22:2002

Electric vehicle conductive charging system - Part 22: AC electric vehicle charging station
Newest version Withdrawn from 15.10.2020