Back

ISO 11414:2009

Plastics pipes and fittings -- Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion

General information

Valid from 29.01.2009
ICS Groups
23.040.60 Flanges, couplings and joints
Directives or regulations
None

Standard history

Status
Date
Type
Name
29.01.2009
Main
ISO 11414:2009
Main
ISO 11414:1996
ISO 11414:2009 specifies a method for preparing butt-fusion-jointed test piece assemblies between polyethylene (PE) pipes and spigot-ended fittings.
ISO 11414:2009 specifies the assembly parameters involved, such as the ambient temperature, joint geometry and fusion parameters, taking into account the service condition limits specified in the relevant product standards, as well as the type of pipe to be used.
ISO 11414:2009 is intended to enable the effect of site assembly variables on joint performance to be determined. The fusion-jointing procedures and parameters used in the field can differ from those in ISO 11414:2009, depending on the manufacturer's written procedures and/or local standards.

Required fields are indicated with *

*
*
*
PDF
82.61 € incl tax
Paper
82.61 € incl tax
Standard monitoring
English (PDF 141 KB)

Related products

Main

EVS-EN 1092-1:2018

Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 1: Steel flanges
Newest version Valid from 03.05.2018
Main + amendment

EVS-EN 1092-1:2007+A1:2013

Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 1: Steel flanges
Withdrawn from 03.05.2018
Main

EVS-EN 1591-1:2014

Flanges and their joints - Design rules for gasketed circular flange connections - Part 1: Calculation
Newest version Valid from 04.02.2014
Main

EVS-EN 1092-2:1999

Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges
Withdrawn from 15.12.2023

Customers who bought this item also bought

Main

ISO 13953:2001

Polyethylene (PE) pipes and fittings -- Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
Newest version Valid from 25.10.2001
Main

EVS-EN 12007-2:2012

Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 2: Specific functional requirements for polyethylene (MOP up to and including 10 bar)
Newest version Valid from 05.09.2012
Main

EVS-EN 12201-5:2011

Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system
Withdrawn from 15.02.2024
Main

EVS-EN 1555-5:2010

Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system
Withdrawn from 20.07.2021

Standards designation

EVS Estonian standard
EN European standard (published by an CEN or CENELEC)
EN ISO International standard adopted as an European standard
ISO International Organization for Standardization’s standard
IEC International Electrotechnical Commission’s standard
HD CENELEC’s harmonisation document
   
EVS-EN European standard implemented in Estonia
EVS-EN ISO International standard adopted in Europe and implemented in Estonia
EVS-EN ISO/IEC International standard/International electrotechnical standard adopted in Europe and implemented in Estonia
EVS-IEC International electrotechnical standard implemented in Estonia
EVS-ISO International standard implemented in Estonia
   
A, AMD amedment
+A a full standard plus the amendment
/A only amendment
COR, AC corrigendum
+COR a full standard plus the corrigendum
NA national annex
+NA a full standard plus the national annex
/NA only national annex
TS technical specification
TR technical report
CWA agreement, developed by a CEN or CENELEC
prEVS-EN (etc) draft standard
   
et the standard is in Estonian only
en the standard is in English only
et-en the standard is in Parallel text Estonian-English