Tagasi

EVS-EN 14025:2018

Tanks for the transport of dangerous goods - Metallic pressure tanks - Design and construction

Üldinfo
Kehtetu alates 29.12.2023
Alusdokumendid
EN 14025:2018
Direktiivid või määrused
puuduvad

Standardi ajalugu

Staatus
Kuupäev
Tüüp
Nimetus
29.12.2023
Põhitekst
02.04.2020
Parandus
01.08.2018
Põhitekst
05.07.2016
Põhitekst + muudatus
EVS-EN 14025:2013+A1:2016
This document specifies the minimum requirements for the design and construction of metallic pressure tanks having a maximum working pressure exceeding 50 kPa (0,5 bar), for the transport of dangerous goods by road and rail and sea. This document includes requirements for openings, closures and structural equipment; it does not cover requirements of service equipment. For tanks for the transport of cryogenic liquids, EN 13530 1 and EN 13530 2 apply.
Design and construction of pressure tanks according to the Scope of this document are primarily subject to the requirements of RID/ADR, Subsections 6.8.2.1, 6.8.3.1 and 6.8.5, as relevant. In addition, the relevant requirements of RID/ADR, Table A, columns 12 and 13, to Chapters 3.2, 4.3 and Subsection 6.8.2.4 apply. For the structural equipment RID/ADR, Subsections 6.8.2.2 and 6.8.3.2 apply, as relevant. The definitions of RID/ADR, Subsection 1.2.1, are referred to. For portable tanks see also RID/ADR, Chapter 4.2 and Sections 6.7.2 and 6.7.2. In addition, the relevant requirements of RID/ADR, Table A, Columns 10 and 11 to Chapters 3.2, 4.2, and Sections 6.7.2 and 6.7.3 apply. The paragraph numbers above relate to the 2017 issue of RID/ADR which are subject to regular revisions. This can lead to temporary non-compliances with EN 14025.
This document is applicable to liquefied gases including LPG; however for a dedicated LPG standard see EN 12493.
If not otherwise specified, provisions which take up the whole width of the page apply to all kind of tanks. Provisions contained in a single column apply only to:
tanks according to RID/ADR Chapter 6.8 (left-hand column);  portable tanks according to RID/ADR Chapter 6.7 (right-hand column).
*
*
*
PDF
28,06 € koos KM-ga
Paber
28,06 € koos KM-ga
Sirvi standardit alates 2,44 € koos KM-ga
Standardi monitooring

Teised on ostnud veel

Põhitekst

EVS-EN 13317:2018

Tanks for transport of dangerous goods - Service equipment for tanks - Manhole cover assembly
Uusim versioon Kehtiv alates 01.08.2018
Põhitekst

EVS-EN 12972:2018

Tanks for transport of dangerous goods - Testing, inspection and marking of metallic tanks
Uusim versioon Kehtiv alates 16.07.2018
Muudatus

EVS-EN ISO 21809-3:2016/A1:2020

Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 3: Field joint coatings - Amendment 1: Introduction of mesh-backed coating systems (ISO 21809-3:2016/Amd 1:2020)
Uusim versioon Kehtiv alates 15.04.2020
Põhitekst + muudatus

EVS-EN 13094:2020+A1:2022

Tanks for the transport of dangerous goods - Metallic gravity-discharge tanks - Design and construction
Uusim versioon Kehtiv alates 01.06.2022