Tagasi

EVS-EN IEC 61000-6-8:2020

Electromagnetic compatibility (EMC) - Part 6-8: Generic standards - Emission standard for professional equipment in commercial and light-industrial locations

Üldinfo
Kehtiv alates 02.10.2020
Alusdokumendid
EN IEC 61000-6-8:2020; IEC 61000-6-8:2020
Tegevusala (ICS grupid)
33.100.10 Kiirgus
Direktiivid või määrused
puuduvad
Standardi ajalugu
Staatus
Kuupäev
Tüüp
Nimetus
02.10.2020
Põhitekst
IEC 61000-6-8: 2020 is a generic EMC emission standard and is applicable only if no relevant dedicated product or product family EMC emission standard has been published. This part of IEC 61000 for emission requirements applies to electrical and electronic equipment intended for use in commercial and light-industrial (see 3.1.3) locations. This document applies to equipment that satisfy the following restrictions of use: - is defined as professional equipment (see 3.1.13), - is professionally installed and maintained (see 3.1.14 and Clause 6), - is not intended to be used in residential locations (see 3.1.16). IEC 61000-6-3 applies to electrical and electronic equipment intended for use at commercial and light-industrial locations that do not satisfy these restrictions. The intention is that all equipment used in the residential, commercial and light-industrial environments are covered by IEC 61000-6-3 or IEC 61000-6-8. If there is any doubt, the requirements in IEC 61000-6-3 apply. Emission requirements within the frequency range 0 Hz to 400 GHz are covered. The conducted and radiated emission requirements in the frequency range up to 400 GHz are considered essential and have been selected to provide an adequate level of protection of radio reception in the defined electromagnetic environment. Not all disturbance phenomena have been included for testing purposes but only those considered relevant for the equipment intended to operate within the locations included within this document. The emission requirements in this document are not intended to be applicable to the intentional transmissions and their harmonics from a radio transmitter as defined by the ITU. NOTE 1 Safety considerations are not covered by this document. NOTE 2 In special cases, situations will arise where the levels specified in this document will not offer adequate protection; for example where a sensitive receiver is used in close proximity to an equipment. In these instances, employ special mitigation measures to reduce any impact. NOTE 3 Disturbances generated in fault conditions of equipment are not covered by this document. NOTE 4 Equipment which complies with IEC 61000-6-3 are suitable for use within these defined locations.
*
*
*
PDF
17,63 € koos KM-ga
Paber
17,63 € koos KM-ga
Hind: 2,40 € koos KM-ga
Standardi monitooring
Teised on ostnud veel
Põhitekst

EVS-EN IEC 61000-6-4:2019

Elektromagnetiline ühilduvus. Osa 6-4: Erialased põhistandardid. Tööstuskeskkondade kiirguslike häiringute standard
Uusim versioon Kehtiv alates 01.10.2019
Põhitekst + muudatus

EVS-EN IEC 55016-1-4:2019+A1:2020

Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Antennas and test sites for radiated disturbance measurements (CISPR 16-1-4:2019 + CISPR 16-1-4:2019/A1:2020)
Uusim versioon Kehtiv alates 17.08.2020
Põhitekst

EVS-EN IEC 61000-6-1:2019

Elektromagnetiline ühilduvus. Osa 6-1: Erialased põhistandardid. Häiringutaluvus olme-, kaubandus- ja väiketööstuskeskkondades
Uusim versioon Kehtiv alates 01.03.2019
Põhitekst

EVS-EN IEC 61000-6-2:2019

Elektromagnetiline ühilduvus. Osa 6-2: Erialased põhistandardid. Häiringutaluvus tööstuskeskkondades
Uusim versioon Kehtiv alates 01.03.2019