Skip to main content
Tagasi

EVS-EN IEC 61400-21-2:2023

Wind energy generation systems - Part 21-2: Measurement and assessment of electrical characteristics - Wind power plants

Üldinfo

Kehtiv alates 01.06.2023
Alusdokumendid
IEC 61400-21-2:2023; EN IEC 61400-21-2:2023
Direktiivid või määrused
puuduvad

Standardi ajalugu

Staatus
Kuupäev
Tüüp
Nimetus
01.06.2023
Põhitekst
IEC 61400-21-2 - Wind energy generation systems - Measurement and assessment of electrical characteristics - Wind power plants - has the following scope: IEC 61400-21-2 defines and specifies the quantities that shall be determined to characterize the electrical characteristics of grid-connected power plants (PP).
IEC 61400-21-2 defines the measurement and test procedures for quantifying the electrical characteristics as basis for the verification of compliance of PP, including:
- Power quality aspects
- Steady state operation
- Dynamic response (undervoltage and overvoltage fault ride-through)
- Disconnection from grid (Grid protection)
- Control performance
IEC 61400-21-2 defines a uniform functionality test and measurement procedure for the power plant controller (PPC), as a basis for the unit test of the power plant controller.
IEC 61400-21-2 defines the procedures for assessing compliance with electrical connection requirements, including the aggregation methods for power quality aspects such as voltage variations, flicker, harmonics and interharmonics.
IEC 61400-21-2 defines the procedures for measurement and fault recording for the verification of power plant electrical simulation models in relation to undervoltage and overvoltage ride through events.
These measurement procedures are valid for power plants, including the power plant controller and other connected equipment, necessary for the operation of the Power Plant. The measurement procedures are valid for any size of power plant connected to the point of connection (POC) at one connection point.
The procedures for assessing and verifying the compliance with grid connection requirements are valid for power plants in power systems with fixed frequency and a sufficient short-circuit power.
Out of the scope of this standard are:
- Multi park control, i.e. cluster management of several power plants (PP) or several connection points
- Compliance test and performance requirements, including pass or fail criteria
- Specific component test and validation of the PP equipment (switchgear, cables, transformers, etc.), which are covered by other IEC standards
- Wind power plant model validation, as defined in the IEC 61400-27-2
- Load flow calculation methods and load flow study guidelines
- Test and measurement of the communication interface and system of the PP as defined in the IEC 61400-25 series
NOTE
For the purposes of this document, the following terms for system voltage apply, based on IEC 60038
Low voltage (LV) refers to 100 V < Un ≤ 1 kV;
Medium voltage (MV) refers 106 to 1 kV < Un ≤ 35 kV;
High voltage (HV) refers to 35 kV < Un ≤ 230 kV;
Extra high voltage (EHV) refers to Un > 230 kV

Nõutud väljad on tähistatud *

*
*
*
PDF
39,04 € koos KM-ga
Paber
39,04 € koos KM-ga
Sirvi standardit alates 2,44 € koos KM-ga
Standardi monitooring

Teised on ostnud veel

Põhitekst

EVS-EN IEC 61400-21-1:2019

Wind energy generation systems - Part 21-1: Measurement and assessment of electrical characteristics - Wind turbines
Uusim versioon Kehtiv alates 01.08.2019
Põhitekst

EVS-EN 50549-1:2019

Nõuded jaotusvõrkudega paralleelselt ühendatud tootmisüksustele. Osa 1: Ühendus madalpingejaotusvõrguga. Tootmisüksused kuni tüübini B (kaasa arvatud)
Kehtiv alates 15.02.2019
Põhitekst

EVS-EN 50549-2:2019

Nõuded jaotusvõrkudega paralleelselt ühendatud tootmisüksustele. Osa 2: Ühendus keskpingejaotusvõrguga. Tootmisüksused kuni tüübini B (kaasa arvatud)
Kehtiv alates 15.02.2019
Põhitekst

EVS-EN 50549-10:2022

Requirements for generating plants to be connected in parallel with distribution networks - Part 10: Tests for conformity assessment of generating units
Uusim versioon Kehtiv alates 15.11.2022