Tagasi

EVS-EN ISO 12215-5:2019

Väikelaevad. Kerekonstruktsioon ja dimensioneerimine. Osa 5: Arvutuslik surve monokerele, arvutuslikud pinged, sõrestikuga seotud arvutused

Üldinfo
Kehtiv alates 02.07.2019
Alusdokumendid
ISO 12215-5:2019; EN ISO 12215-5:2019
Tegevusala (ICS grupid)
47.080 Väikelaevad
Direktiivid või määrused
2013/53/EU Väikelaevad ja jetid
Standardi ajalugu
Staatus
Kuupäev
Tüüp
Nimetus
02.07.2019
Põhitekst
16.10.2018
Põhitekst
This document defines the dimensions, design local pressures, mechanical properties and design stresses for the scantlings determination of monohull small craft with a hull length (LH) or a load line length (see NOTE 1) of up to 24 m. It considers all parts of the craft that are assumed to be watertight or weathertight when assessing stability, freeboard and buoyancy in accordance with ISO 12217. NOTE 1 The load line length is defined in the IMO "International Load Lines Convention 1966/2005", it can be larger than LH for craft with overhangs. This length also sets up at 24 m the lower limit of several IMO conventions. The main core of this document determines the local design pressures and stresses for monohulls and details the possible scantlings methods derived from these pressures and stresses, both for monohulls and multihulls (see NOTE 2). The assessment process requires, where relevant, the application of Annexes. This document is applicable to small craft, in intact condition, of the two following types: — recreational craft, including recreational charter vessels; — small commercial craft and workboats, see Clause 12 and Annex J. It is not applicable to racing craft designed only for professional racing. NOTE 2 Local pressures and stresses for multihulls are given in ISO 12215-7. This document is applicable to the structures supporting windows, portlights, hatches, deadlights, and doors. For the complete scantlings of the craft, this document is intended to be used with ISO 12215-8 for rudders, ISO 12215-9 for appendages and ISO 12215-10 for rig loads and rig attachments. This document covers small craft built from the following materials: — fibre-reinforced plastics, either in single skin or sandwich construction; — aluminium or steel alloys; — glued wood or plywood (single skin or sandwich), excluding traditional wood construction; — non-reinforced plastics for craft with a hull length less than 6 m (see Annex D). Throughout this document, unless otherwise specified, dimensions are in (m), areas in (m2), masses in (kg), forces in (N), moments in (N.m), pressures in kN/m2 (1 kN/m2 = 1 kPa), stresses and elastic modulus in N/mm2 (1 N/mm2 = 1 Mpa). Max(a;b;c) means that the required value is the maximum of a, b, and c; and min(d;e;f) means that the required value is the minimum of d, e, and f.
*
*
*
PDF
30,04 € koos KM-ga
Paber
30,04 € koos KM-ga
Hind: 2,40 € koos KM-ga
Standardi monitooring
Teised on ostnud veel
Põhitekst

EVS-EN ISO 12215-6:2018

Small craft - Hull construction and scantlings - Part 6: Structural arrangements and details (ISO 12215-6:2008)
Uusim versioon Kehtiv alates 16.10.2018
Põhitekst

EVS-EN ISO 12215-9:2018

Small craft - Hull construction and scantlings - Part 9: Sailing craft appendages (ISO 12215-9:2012)
Uusim versioon Kehtiv alates 16.10.2018
Põhitekst

EVS-EN ISO 12215-1:2018

Small craft - Hull construction and scantlings - Part 1: Materials: Thermosetting resins, glass-fibre reinforcement, reference laminate (ISO 12215-1:2000)
Uusim versioon Kehtiv alates 02.11.2018
Põhitekst

EVS-EN ISO 12215-8:2018

Small craft - Hull construction and scantlings - Part 8: Rudders (ISO 12215-8:2009, including Cor 1:2010)
Uusim versioon Kehtiv alates 16.10.2018