Skip to main content
Tagasi

CEN/TS 12201-7:2014

Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity

Üldinfo

Kehtiv alates 01.04.2014
Alusdokumendid
CEN/TS 12201-7:2014
Direktiivid või määrused
puuduvad

Standardi ajalugu

Staatus
Kuupäev
Tüüp
Nimetus
01.04.2014
Põhitekst
06.10.2003
Põhitekst
06.10.2003
Põhitekst
This part of EN 12201 gives guidance for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of EN  12201 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001 [1].
NOTE 1  If certification is involved, the certification and inspection body is preferably compliant with EN 45011 [2ISO/IEC 17065 [5], EN 45012ISO/IEC 17021 [3] or EN ISO/IEC 17020 [42], as applicable.
In conjunction with Parts 1 to 5 of EN  12201 (see Foreword) this document is applicable to polyethylene (PE) plastics piping systems for water supply, and for drainage and sewerage under pressure. It is applicable to PE pipes, fittings, and valves, their joints and to joints with components of other materials intended to be used under the following conditions:
a)  allowable operating pressure, PFA, up to 25 bar 1 );
b)  an operating temperature of 20  °C as a reference temperature;
c)  buried in the ground;
d)  sea outfalls;
e)  laid in water;
f)  above ground, including pipes suspended below bridges.
NOTE 2  For applications operating at constant temperature greater than 20  °C and up to 40  °C, see EN  12201- 1:2011, Annex  A.
NOTE 3  It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.

Nõutud väljad on tähistatud *

*
*
*
PDF
26,84 € koos KM-ga
Paber
26,84 € koos KM-ga
Sirvi standardit alates 2,44 € koos KM-ga
Standardi monitooring

Teised on ostnud veel

Põhitekst

EVS-EN 12201-1:2011

Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General
Kehtetu alates 15.02.2024
Põhitekst + muudatus

EVS-EN 12201-2:2011+A1:2013

Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes
Kehtetu alates 15.02.2024
Põhitekst

EVS-EN 10240:1999

Terastorude sise- ja/või väliskaitsekatted. Automatiseeritud tehastes kuumsukelgalvaanimise teel valmistatud katete tehnilised andmed
Uusim versioon Kehtiv alates 01.01.2000
Põhitekst + muudatus

EVS-EN 10255:2004+A1:2007

Keevitamiseks ja keermestamiseks sobivad süsinikterasest torud. Tehnilised tarnetingimused KONSOLIDEERITUD TEKST
Uusim versioon Kehtiv alates 06.06.2007