Tagasi

EVS-EN 16602-60-13:2015

Space product assurance - Requirements for the use of COTS components

Üldinfo
Kehtetu alates 17.07.2023
Alusdokumendid
ECSS-Q-ST-60-13C; EN 16602-60-13:2015
Direktiivid või määrused
puuduvad

Standardi ajalugu

Staatus
Kuupäev
Tüüp
Nimetus
17.07.2023
Põhitekst
02.09.2015
Põhitekst
This standard defines the requirements for selection, control, procurement and usage of EEE commercial components for space projects.
This standard is applicable to commercial encapsulated active monolithic parts (integrated circuits and discrete):
•  diodes
•  microwave diodes
•  integrated circuits
•  microwave integrated circuits (MMIC)
•  transistors
•  microwave transistors
This standard is not applicable to the commercial parts from the following families:
•  capacitors
•  connectors
•  crystals
•  filters
•  fuses
•  heaters
•  inductors
•  microwave passive parts
•  oscillators
•  relays
•  resistors
•  switches
•  thermistors
•  transformers
•  cables & wires
•  hybrids
•  surface acoustic waves (SAW)
•  charge coupled devices (CCD)
•  active pixel sensors (APS)
In addition, the following families of EEE components are not addressed by the present ECSS standard but it can be used as guideline and revisited on case/case basis:
•  photodiodes
•  light emitting diodes (LED)
•  phototransistors
•  opto-couplers
•  laser diodes
In line with ECSS-Q-ST-60, this standard differentiates between three classes of components through three different sets of standardization requirements (clauses) to be met.
The three classes provide for three levels of trade-off between assurance and risk. The highest assurance and lowest risk is provided by class 1 and the lowest assurance and highest risk by class 3. Procurement costs are typically highest for class 1 and lowest for class 3. Mitigation and other engineering measures can decrease the total cost of ownership differences between the three classes. The project objectives, definition and constraints determine which class or classes of components are appropriate to be utilised within the system and subsystems.
a.  Class 1 components are described in Clause 4
b.  Class 2 components are described in Clause 5
c.  Class 3 components are described in Clause 6
Annex G includes a diagram that summarizes the difference between these three classes for evaluation, screening and lot acceptance.
The requirements of this document are applicable to all parties involved at all levels in the integration of EEE commercial components into space segment hardware and launchers.
For easy tailoring and implementation of the requirements into a Requirement Management Tool, and for direct traceability to ECSS-Q-ST-60, requirements in this standards have been written in the way of a ECSS Applicability Requirement Matrix (EARM), as defined in Annex A of ECSS-S-ST-00 “ECSS system – Description, implementation and general requirements”.
This standard may be tailored for the specific characteristics and constrains of a space project in conformance with ECSS-S-ST-00.
*
*
*
PDF
34,16 € koos KM-ga
Paber
34,16 € koos KM-ga
Sirvi standardit alates 2,44 € koos KM-ga
Standardi monitooring

Teised on ostnud veel

Põhitekst

EVS-EN 16602-70-31:2014

Space product assurance - Application of paints and coatings on space hardware
Uusim versioon Kehtiv alates 09.12.2014
Põhitekst

EVS-EN 16602-70-04:2014

Space product assurance - Thermal testing for the evaluation of space materials, processes, mechanical parts and assemblies
Uusim versioon Kehtiv alates 07.11.2014
Põhitekst

EVS-EN 16602-70-13:2015

Space product assurance - Measurements of the peel and pull-off strength of coatings and finishes using pressure-sensitive tapes
Uusim versioon Kehtiv alates 04.03.2015
Põhitekst

EVS-EN IEC 60812:2018

Failure modes and effects analysis (FMEA and FMECA)
Uusim versioon Kehtiv alates 02.11.2018