Tagasi

EVS-EN ISO 19069-1:2015

Plastid. Polüpropüleenist (PP) vormimis- ja ekstrusioonimaterjalid. Osa 1: Tähistussüsteem ja tehniliste andmete alused

Üldinfo
Kehtiv alates 02.04.2015
Alusdokumendid
EN ISO 19069-1:2015; ISO 19069-1:2015
Tegevusala (ICS grupid)
83.080.20 Termoplastid
Direktiivid või määrused
puuduvad
Standardi ajalugu
Staatus
Kuupäev
Tüüp
Nimetus
02.04.2015
Põhitekst
01.01.2000
Põhitekst
1.1 This part of ISO 19069 establishes a system of designation for polypropylene (PP) thermoplastic material, which may be used as the basis for specifications. 1.2 The types of polypropylene plastics are differentiated from each other by a classification system based on appropriate levels of the designatory properties a) tensile modulus of elasticity b) impact strength c) melt mass-flow rate (MFR) and on information about basic polymer parameters, intended application and/or method of processing, important properties, additives, colorants, fillers and reinforcing materials. 1.3 This part of ISO 19069 is applicable to all polypropylene homopolymers and to copolymers of propylene with a content of other 1-olefinic of less than 50 % (m/m), as well as blends of polymers containing at least 50 % (m/m) of aforementioned polymers. It applies to materials ready for normal use in the form of powder, granules or pellets and to materials unmodified or modified by colorants, additives, fillers, etc. This part of ISO 19069 does not apply to propylene-based rubber. 1.4 It is not intended to imply that materials having the same designation give necessarily the same performance. This part of ISO 19069 does not provide engineering data, performance data or data on processing conditions which may be required to specify a material for a particular application and/or method of processing. If such additional properties are required, they shall be determined in accordance with the test methods specified in part 2 of this International Standard, if suitable. 1.5 In order to specify a thermoplastic material for a particular application or to ensure reproducible processing, additional requirements may be given in data block 5 (see clause 3, introductory paragraph).
*
*
*
PDF
10,46 € koos KM-ga
Paber
10,46 € koos KM-ga
Sirvi standardit: 2,40 € koos KM-ga
Standardi monitooring
Teised on ostnud veel
Põhitekst

EVS-EN ISO 17855-1:2014

Plastics - Polyethylene (PE) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 17855-1:2014)
Uusim versioon Kehtiv alates 09.12.2014
Põhitekst

EVS-EN ISO 18743:2015

Toiduahela mikrobioloogia. Keeritsussivastsete (Trichinella) määramine lihas tehisseedemeetodil
Uusim versioon Kehtiv alates 04.11.2015
Põhitekst

EVS-EN ISO 17855-2:2016

Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 17855-2:2016)
Uusim versioon Kehtiv alates 04.04.2016
Põhitekst

EVS-EN ISO 16396-1:2015

Plastics - Polyamide (PA) moulding and extrusion materials - Part 1: Designation system, marking of products and basis for specifications (ISO 16396-1:2015)
Uusim versioon Kehtiv alates 02.04.2015