Back

EVS-EN ISO 15875-2:2025

Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 2: Pipes (ISO 15875-2:2025)

General information

Valid from 17.11.2025
Base Documents
ISO 15875-2:2025; EN ISO 15875-2:2025
ICS Groups
23.040.20 Plastics pipes 91.140.60 Water supply systems
Directives or regulations
None

Standard history

Status
Date
Type
Name
17.11.2025
Main
EVS-EN ISO 15875-2:2025
31.12.2020
Amendment
EVS-EN ISO 15875-2:2004/A2:2020
06.08.2007
Amendment
EVS-EN ISO 15875-2:2004/A1:2007
13.05.2004
Main
EVS-EN ISO 15875-2:2004
This document specifies the characteristics of pipes for crosslinked polyethylene (PE-X) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not intended for human consumption (domestic systems), and for heating systems, under design pressures and temperatures according to the class of application (see ISO 15875-1:2025, Table 1).
This document also specifies the test parameters for the test methods referred to in this document.
It is applicable to PE-X pipes with and without barrier layer.
This document is applicable to PE-X pipes for hot and cold water installations, which are intended to be connected to fittings conforming to ISO 15875-3, whereby the joints conform to the requirements of ISO 15875-5.

Required fields are indicated with *

*
*
*
PDF
24.80 € incl tax
Paper
24.80 € incl tax
Browse standard from 2.48 € incl tax
Standard monitoring
English (PDF 1 MB)

Related products

Main

EVS 835:2014

Water supply systems inside buildings
Withdrawn from 01.04.2022
Main

EVS 921:2014

Water supply systems outside buildings
Withdrawn from 01.04.2022
Main

EVS 835:2022

Water supply systems inside buildings
Newest version Valid from 01.04.2022
Main

EVS 921:2022

Water supply systems outside buildings
Newest version Valid from 01.04.2022

Customers who bought this item also bought

Main

EVS-EN 1451-1:2017

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
Newest version Valid from 01.12.2017
Main

CEN ISO/TS 15875-7:2018

Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 7: Guidance for the assessment of conformity (ISO/TS 15875-7:2018)
Newest version Valid from 03.01.2019
Main

CEN/TS 1451-2:2019

Plastic piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity
Newest version Valid from 16.12.2019
Main

EVS-EN ISO 527-4:2023

Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites (ISO 527-4:2023)
Newest version Valid from 02.05.2023

Standards designation

EVSEstonian standard
ENEuropean standard (published by an CEN or CENELEC)
EN ISOInternational standard adopted as an European standard
ISOInternational Organization for Standardization’s standard
IECInternational Electrotechnical Commission’s standard
HDCENELEC’s harmonisation document
EVS-ENEuropean standard implemented in Estonia
EVS-EN ISOInternational standard adopted in Europe and implemented in Estonia
EVS-EN ISO/IECInternational standard/International electrotechnical standard adopted in Europe and implemented in Estonia
EVS-IECInternational electrotechnical standard implemented in Estonia
EVS-ISO International standard implemented in Estonia
 
A, AMDamedment
+Aa full standard plus the amendment
/Aonly amendment
COR, ACcorrigendum
+CORa full standard plus the corrigendum
NAnational annex
+NAa full standard plus the national annex
/NAonly national annex
TStechnical specification
TRtechnical report
CWAagreement, developed by a CEN or CENELEC
prEVS-EN (etc)draft standard
 
etthe standard is in Estonian only
enthe standard is in English only
et-enthe standard is in Parallel text Estonian-English